Cornelius SPIRIT Скачать руководство пользователя страница 34

Страница: 34 / 41

317961000

WARNING: If repairs are to be made to a product system, remove quick disconnects from
the applicable product tank, then relieve the system pressure before proceeding. If repairs
are to be made to the CO

system, stop dispensing, shut off the CO

supply, then relieve the

system pressure before proceeding. If repairs are to be made to the refrigeration system, make sure
electrical power is disconnected from the unit.

TROUBLESHOOTING

IMPORTANT: Only qualified personnel should service internal components or electrical wiring.

TROUBLESHOOTING DISPENSING SYSTEM

Trouble

Probable Cause

Remedy

WATER-TO-SYRUP ‘‘RATIO’’
TOO LOW OR TOO HIGH.

Dispensing valve syrup flow
regulator not properly
adjusted.

Adjust Water-to-Syrup ‘‘Ratio’’ of
dispensed drink as instructed.

gas pressure to syrup

tanks insufficient to push syrup
out of tank.

Adjust syrup tanks secondary
CO

regulator as instructed.

ADJUSTMENT OF
DISPENSING VALVE SYRUP
FLOW REGULATOR DOES
NOT INCREASE TO DESIRED
WATER-TO-SYRUP ‘‘RATIO’’.

No syrup supply.

Replenish syrup supply as
instructed.

Syrup tank quick disconnects
not secure.

Secure quick disconnects.

Syrup tanks secondary CO

regulator out of adjustment.

Adjust syrup tanks secondary
CO

regulator as instructed.

Dispensing valve syrup flow
regulator, syrup tank quick
disconnect, or syrup line
restricted.

Sanitize syrup system as
instructed.

Improper syrup Baume.

Replace syrup supply as
instructed.

Dirty or inoperative piston or
spring in dispensing valve
syrup flow regulator.

Disassemble and clean
dispensing valve syrup flow
regulator.

Tapered nylon washer inside
tube swivel nut connector
distorted from being
overtightened.

Replace nylon washer and make
sure it seats properly.

Содержание SPIRIT










































Результаты поиска

Содержание SPIRIT

Отзывы:

Похожие инструкции для SPIRIT

Бренды по названию

Популярные бренды

Cornelius SPIRIT, Руководство по установке

Результаты поиска

Содержание SPIRIT

Отзывы:

Похожие инструкции для SPIRIT

Бренды по названию

Популярные бренды