eco3energy PAW-TD20C1E5-UK Скачать руководство пользователя

Страница: 1 / 16

PLEASE LEAVE THIS MANUAL WITH THE UNIT AFTER INSTALLATION

145963-06 04-2019

Installation Manual

PAW-TD20/30C1E5-UK

PAW-TD20/30C1E5-UK-1

Thank-you for purchasing the PAW unvented hot water cylinder.

The PAW is an unvented hot water cylinder in capacities 200 and 300 litres. Its energy efficiency as defined by standing

heat losses is the best in its class and will save the householder significant energy costs over the lifetime of the cylinder.

This manual gives detailed advice for installation and should be read carefully prior to fitting any unvented unit. PAW cylin

ders are not suitable for gravity fed primary systems. In known hard water regions, precautions should be taken to prevent

limescale formation in hot water cylinders, in accordance with Building Regulation Part L, Domestic Heating Compliance

Guide.

This cylinder must be installed by a competent person and be installed in compliance with the Installation and Maintenance

Instructions, all current legislation, codes of practice and regulations governing the installation of unvented hot water cylin

ders in force at the date of installation.

Contents

Page no.

1. General information

...........................2

2. Preparation of installation area

..........4

3. Pipe connections ...............................4

4. Commissioning and filling up

.............5

5. Draining and Flushing ........................5

6. Electrical installation ..........................5

7. Safety and Servicing

..........................9

8. Fault finding

.....................................10

9. Technical and Performance specs

... 11

10. Warranty ..........................................12

11. Log book

..........................................13

PLEASE READ THIS MANUAL BEFORE INSTALLATION AND LEAVE WITH THE UNIT.

THE MANUAL AND ATTACHED LOGBOOK SERVE AS THE CYLINDER GUARANTEE.

This cylinder is manufactured and approved in accordance with EN 12897 : 2006

Содержание PAW-TD20C1E5-UK

















Результаты поиска

Содержание PAW-TD20C1E5-UK

Отзывы:

Похожие инструкции для PAW-TD20C1E5-UK

Бренды по названию

Популярные бренды

eco3energy PAW-TD20C1E5-UK, Руководство по установке

Результаты поиска

Содержание PAW-TD20C1E5-UK

Отзывы:

Похожие инструкции для PAW-TD20C1E5-UK

Бренды по названию

Популярные бренды