background image

13

The code of practice for the installation,

commissioning & servicing of mains pressure hot water storage

Installation,Commissioning 

and Service Record Log Book

CUSTOMER DETAILS

NAME
ADDRESS

TEL No.

IMPORTANT

1. Please, keep the Log Book in a safe place for future reference.
2. This Log Book is to be completed in full by the competent person(s) who

commissioned the equipment and then handed to the customer. When this is done,

the Log Book is a commissioning certificate that can be accepted as evidence of

compliance with the appropriate Building Regulations.

3. Failure to install and commission this appliance to the manufacturer’s

  instructions may invalidate the guarantee.

The above does not affect your statutory rights.

INSTALLER & COMMISSIONING ENGINEER DETAILS

INSTALLER DETAILS

COMPANY NAME

DATE

ADDRESS

INSTALLER NAME

TEL No.

REGISTERED OPERATIVE ID CARD No.

(IF APPLICABLE)

REGISTRATION DETAILS

COMMISSIONING ENGINEER (IF DIFFERENT)

NAME

DATE

ADDRESS

TEL No.

REGISTERED OPERATIVE ID CARD No.

(IF APPLICABLE)

REGISTRATION DETAILS

IT IS THE RESPONSIBILITY OF THE INSTALLER TO COMPLETE THIS LOGBOOK AND PASS IT 

ON TO THE CUSTOMER. FAILURE TO DO SO MAY INVALIDATE THE CYLINDER GUARANTEE

Содержание PAW-TD20C1E5-UK

















Отзывы: