background image

14

APPLIANCE & TIME CONTROL DETAILS

MANUFACTURER

MODEL

CAPACITY

TYPE
TIME CONTROL

UNVENTED
PROGRAMMER

litres

SERIAL No.

TIME SWITCH

or

COMMISSIONING PROCEDURE INFORMATION

BOILER PRIMARY SETTINGS (INDIRECT HEATING ONLY) ALL BOILERS

IS THE PRIMARY A SEALED OR OPEN VENTED SYSTEM?

SEALED

OPEN

WHAT IS THE INDIRECT HEAT SOURCE  FLOW TEMPERATURE?

   

  C

ALL MAINS PRESSURISED SYSTEMS

YES

WHAT IS INCOMING STATIC COLD WATER PRESSURE AT THE INLET TO THE

PRESSURE REDUCING VALVE?
HAS STRAINER (IF FITTED) BEEN CLEANED OF INSTALLATION DEBRIS?
HAS A WATER SCALE REDUCER BEEN FITTED?
WHAT TYPE OF SCALE REDUCER HAS BEEN FITTED?

NO

YES

NO

UNVENTED SYSTEMS

YES

ARE COMBINED TEMPERATURE AND PRESSURE RELIEF VALVE

AND EXPANSION VALVE FITTED AND DISCHARGE TESTED?
IS PRIMARY ENERGY SOURCE CUT OUT FITTED

(NORMALLY 2 PORT VALVE)?
WHAT IS THE PRESSURE REDUCING VALVE SETTING (IF FITTED)?
WHERE IS OPERATING PRESSURE REDUCING VALVE SITUATED?

NO

YES

NO

bar

HAS THE EXPANSION VESSEL OR INTERNAL AIR SPACE BEEN CHECKED? YES

NO

WHAT IS THE HOT WATER TEMPERATURE AT THE NEAREST OUTLET?

   

  C

bar

ALL PRODUCTS

YES

DOES THE HOT WATER SYSTEM COMPLY WITH

THE APPROPRIATE BUILDING REGULATIONS?
HAS THE SYSTEM BEEN INSTALLED AND COMMISSIONED

IN ACCORDANCE WITH THE MANUFACTURER’S INSTRUCTIONS?
HAVE YOU DEMONSTRATED THE OPERATION OF THE 

SYSTEM CONTROLS TO THE CUSTOMER?

YES

YES

HAVE YOU LEFT ALL THE MANUFACTURER’S 

LITERATURE WITH THE CUSTOMER?

YES

COMPETENT PERSON’S 

SIGNATURE

CUSTOMER’S

SIGNATURE

(To confirm demonstrations of equipment and

receipt of appliance instructions)

PLEASE FOLLOW THE INSTALLATION AND COMMISSIONING INSTRUCTIONS

IN THE INSTALLATION MANUAL SUPPLIED WITH THE EQUIPMENT

Содержание PAW-TD20C1E5-UK

















Отзывы: