Cooper Wheelock SAFEPATH 4 SP4-TZC Скачать руководство пользователя страница 43

Страница: 43 / 51

5.2 General Trouble Adjustments

1. The system volume of the Background Music is too loud or too soft. Adjust R17 (BGM Volume Adjust)

shown on Figure 17.

2. The system volume of the page is too loud or too soft. Adjust R7 (Page Volume Adjust) shown on Figure 17.

3. The state of the Alert Page Tone is

OFF

and needs to be changed. Move t he Alert Page Tone Selection

Jumper (JP1) according to instructions found on the PC board. See Figure 17.

Alert Page

Tone

Selection

Jumper

BGM

Volume

Adjust

Page

Volume

Adjust

Figure 17

General Trouble Adjustment Locations

5.3 Troubleshooting Using Tone Patterns

The SP4-TZC provides audio tone patterns to help you identify a trouble or the reason a page cannot be
completed. The following table describes these conditions.

Table 6

Troubleshooting Using Tone Patterns

Page Condition

Indication From SP4-TZC

Indication From
SP4-APS

Indication From
SP40

SP40 is in Alarm
condition. No
paging is allowed.

Busy Signal. No page.

None

Open Zone being
paged

No indication. Page will be
broadcast on all trouble free
zones.

Open LED indicator
for that zone.

TROUBLE and
Audio Short LED
indicators.

Shorted Zone being
paged

3 short beeps followed by a
long beep. Page will be
broadcast on all trouble free
zones.

Short LED indicator
for that zone.

TROUBLE and
Audio Short LED
indicators.

Invalid 2-digit
Zone Code entered

3 short beeps followed by a
long beep.

None

Содержание SAFEPATH 4 SP4-TZC



















































Результаты поиска

Содержание SAFEPATH 4 SP4-TZC

Отзывы:

Похожие инструкции для SAFEPATH 4 SP4-TZC

Бренды по названию

Популярные бренды

Cooper Wheelock SAFEPATH 4 SP4-TZC, Инструкция по установке, испытаниям, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SAFEPATH 4 SP4-TZC

Отзывы:

Похожие инструкции для SAFEPATH 4 SP4-TZC

Бренды по названию

Популярные бренды