Cooper Wheelock SAFEPATH 4 SP4-TZC Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 51

Cooper Wheelock SAFEPATH 4 SP4-TZC Скачать руководство пользователя страница 41

41

5.1.2 Resetting the Network Configuration (SP4 Telzone

Programmer 2 Programmed)

Resetting the network configuration is done when it appears that the paging system is corrupt or an SP4-
APS splitter has been added, removed or replaced. Should one of these conditions occur, and the SP4-TZC
has been programmed using the SP4 Telzone Programmer 2 software (“USB CONFIG” LED indicator is

BLINKING

), perform one of these procedures. If you have made changes, use Appendix A at the end of

this manual to update the new Zone Code location for each zone and zone group.

If an SP4-APS splitter has been replaced or there appears to be corruption of the network, perform
Procedure 1. If an SP4-APS splitter has been added or removed, perform Procedure 2.

Procedure 1: Replacing an SP4-APS Splitter in the Same Location or if a Network Corruption has
occurred.

Remove the enclosure cover from the SP4-TZC.

Make sure 24VDC is

ON

to the SP4-TZC and all SP4-APS splitters. Notice that the “USB

CONFIG” LED indicator is

BLINKING

.

Press and hold the system reset switch for approximately 5 seconds until the all LED indicators
except the “POWER” LED indicator turn

OFF

.

Release the system reset switch. The SP4-TZC will begin finding and mapping the SP4-APS
splitters. The “RS485 COM1 ACTIVE” LED indicator should be

BLINKING

. The

“STANDBY/RUN” LED indicator will

BLINK

for a maximum of 1 minute after which the

“STANDBY/RUN” LED will remain

ON

. The “USB CONFIG” LED indicator will change to

solid

ON

.

Install the enclosure cover.

Procedure 2: Adding or Removing SP4-APS Splitter(s)

NOTE:

If an SP4-APS splitter(s) is being added, make sure its Class of Wiring switch (SW2) is in the same

position as all the other SP4-APS splitters Class of Wiring switches.

Remove the enclosure cover for the SP4-TZC.

Make sure 24VDC is

ON

to the SP4-TZC and all SP4-APS splitters. Notice that the “USB

CONFIG” LED indicator is

BLINKING

.

Press and hold the system reset switch for approximately 5 seconds until the all LED indicators
except the “POWER LED” indicator turn

OFF

.

Release the system reset switch. The SP4-TZC will begin finding and mapping the SP4-APS
splitters. The “RS485 COM1 ACTIVE” LED indicator should be

BLINKING

. The

“STANDBY/RUN” LED indicator will

BLINK

for a maximum of 1 minute after which the

“STANDBY/RUN” will remain

ON

. The “USB CONFIG” LED indicator will now be

BLINKING

.

With the system operating, connect the USB cable between the SP4-TZC and the host computer
containing the SP4 Telzone Programmer 2 software.

STEP 1

STEP 2

STEP 3

STEP 4

STEP 5

STEP 1

STEP 2

STEP 3

STEP 4

STEP 5

«
...
39
40
41
42
43
...
»

Содержание SAFEPATH 4 SP4-TZC




















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды