Cooper Wheelock SAFEPATH 4 SP4-TZC Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 51

Cooper Wheelock SAFEPATH 4 SP4-TZC Скачать руководство пользователя страница 29

29

Click the

OK

button on the “Zone Controller Successfully Programmed” message.

Close the SP4 Telzone Programmer 2 software.

Disconnect the USB cable from the SP4-TZC Zone Controller and the host computer.

3.5.2 Manually Programming/Editing Logical Zone Groups

Connect the USB cable from the USB port on the SP4-TZC Zone Controller to the configured
USB port on the host computer. Make sure that the SP40, all Audio Boosters and SP4-APS
splitters are properly connected and powered up.

Start the SP4 Telzone Programmer 2 software.

NOTE:

Before creating a new setup file, always save the current file.

Notice that the file name is

Setup.tzc

. Do one of the following:

a.

If you wish to obtain and view the present setup of Logical Zone Groups, click the

“Get

Configuration”

command button. Then proceed to Step 4.

b. If you wish to select a previously saved setup file, select the

File

menu and click on

Open

. Select the desired file. Then proceed to Step 4.

c.

If you wish to create a new setup file, select

New

from the

File

menu to open the Wizard

and begin. Refer to section 3.5.1.

STEP 1

STEP 2

STEP 3

STEP 17

STEP 18

STEP 1

STEP 19

«
...
27
28
29
30
31
...
»

Содержание SAFEPATH 4 SP4-TZC




















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды