Control Network Solution eNodeIVTM Скачать руководство пользователя

Страница: 73 / 76

September 2011

V1.44

Fig.4.12: Functional Block On Drawing

5. FTT-10 XCVR LonTalk Network Termination

When using an FTT-10 XCVR, the network wiring should be terminated or performance may

suffer. This is especially true for long wire runs or noisy environments. Typically an external

terminator is used. The eNodeIV, however, does have an optional internal terminator for those

applications where it is desirable or convenient to terminate at the router. When the optional

internal terminator is installed, a jumper on header JP1 is used to configure the type of

termination. In order to do this the case must be opened. Disconnect the power and network

before opening the case. Use caution and appropriate electrostatic safety precautions

whenever working with the case removed. If the centre pin of JP1 is jumpered to the pin

labelled

Free

, then the terminator is set for free topology mode. If the centre pin of JP1 is

jumpered to the pin labelled

Bus

, then the terminator is set for bus mode. If the centre pin is

not jumpered to either the Bus or Free pins then the terminator is disabled. The following

figures show photos of JP1 with the jumper in the 3 different settings.

A. Bus

Содержание eNodeIVTM










































































Результаты поиска

Содержание eNodeIVTM

Отзывы:

Похожие инструкции для eNodeIVTM

Бренды по названию

Популярные бренды

Control Network Solution eNodeIVTM, Руководство пользователя

Результаты поиска

Содержание eNodeIVTM

Отзывы:

Похожие инструкции для eNodeIVTM

Бренды по названию

Популярные бренды