Control Network Solution eNodeIVTM Скачать руководство пользователя

Страница: 13 / 76

September 2011

V1.44

1.6.2. Button, Indicators, and Connectors for eNodeIV

Index

Description

Ethernet 10/100 Base-T Port. RJ-45 Cat-5.

Power LED lights when unit powered.

Service LED flashes when a service message sent.

TX LED flashes to indicate send traffic on the LON Port.

RX LED flashes to indicate receive traffic on the LON Port.

LON (709.1) Port. May be either FTT-10 or RS-485 transceiver. Check particular configuration of router.

2 Pin, 5mm spacing screw terminal block.

5 V power input and ground. Ground pin is also ground for RS-485 transceiver when applicable.

Requires regulated 5V. Reverse polarity protected. Reversing polarity for extended time may damage

router. 2 Pin, 5 mm spacing screw terminal block.

Ethernet Link LED lights when link obtained.

Ethernet Traffic LED flashes when traffic on Ethernet port.

Reset Button. Resets and restarts router.

Service Pin Router. Sends out a service message on both LON and IP sides for the router. If 852

bridging router mode is enabled sends out a service message for both 852 channels. Also used for

startup mode selection.

Service Pin Application. Sends out a service message on both LON and IP sides only if optional twin

mode application is activated. Also used for startup mode selection.

WiFi Link LED lights when link obtained. Infrastructure mode solid. Ad Hoc mode, flashing 5 second on,

1 second off. No connection, flashing one second on, one second off.

WiFi Port for optional 802.11b WiFi version. Male RP-SMA screw connector. Mates with Female

RP-SMA antenna or cable.

WiFi Traffic LED flashes when traffic on WiFi port.

1.6.3. Wiring

The standard configuration for the eNodeIV4 has a 4 pin 5.0 mm spaced screw terminal block.

The pins from top to bottom are labelled A, B, (logic ground), and 5VDC. To use the terminal

block unscrew the terminal screws on the block and insert the ends of the appropriate wires

into each opening. Tighten the terminal screws. Pins A and B are the 709.1 LON channel port

Содержание eNodeIVTM










































































Результаты поиска

Содержание eNodeIVTM

Отзывы:

Похожие инструкции для eNodeIVTM

Бренды по названию

Популярные бренды

Control Network Solution eNodeIVTM, Руководство пользователя

Результаты поиска

Содержание eNodeIVTM

Отзывы:

Похожие инструкции для eNodeIVTM

Бренды по названию

Популярные бренды