Control Network Solution eNodeIVTM Скачать руководство пользователя

Страница: 62 / 76

September 2011

V1.44

3.5. Twin Mode Status Page

The

Twin Mode Status Page

displays operational state and statistics information about the

Redundant Twin Mode

operation. Twin mode is an optional enhancement and is not activated

in a standard router. If your device does not support

Redundant Twin Mode

contact Adept to

find out how it might be activated. Following is a brief description of each item listed on the

page.

Fig.3.9: Twin Mode Status Page

Twin Mode Redundancy

: This field indicates whether twin mode is enabled or disabled

(on/off).

Alarm/Fault State

: This field indicates the status of any alarms or faults.

Failure State

: This field indicates the status of any monitoring failures.

Operational State

: This field indicates the twin mode operational state.

Flags

: This field indicates the twin mode operational state flags for debugging.

Seconds Since Clear

: This field indicates the number of seconds since the statistics were last

cleared.

Arb Count

: This field indicates this device’s arbitration count.

Twin Arb Count

: This field indicates the twin’s arbitration count.

Total Arbitrations

: This field indicates the total number of active state arbitrations.

Forward Rate

: This field indicates the rate in packets per second of packets forwarded by the

router in either direction.

Содержание eNodeIVTM










































































Результаты поиска

Содержание eNodeIVTM

Отзывы:

Похожие инструкции для eNodeIVTM

Бренды по названию

Популярные бренды

Control Network Solution eNodeIVTM, Руководство пользователя

Результаты поиска

Содержание eNodeIVTM

Отзывы:

Похожие инструкции для eNodeIVTM

Бренды по названию

Популярные бренды