Control Network Solution eNodeIVTM Скачать руководство пользователя

Страница: 61 / 76

September 2011

V1.44

Status SNVT Update Time

: The twin monitoring application has a status SNVT type 93. If bound

the status SNVT is propagated either on a timer or when it is updated by the monitoring

application or both or neither. The Status SNVT update time determines the maximum time

between propagations. If the update time is non zero, every update time ms a status SNVT is

scheduled for propagation. It is propagated even if the status has not been updated. If the

update time is zero then no propagation is scheduled on a timed interval. For a more detailed

description of the Status SNVT see Section 2.5.5.

Status SNVT Send on Update

: This option schedules the status SNVT for propagation whenever

the SNVT is updated or the status changes. This is event driven and not time driven. For a more

detailed description of the status SNVT see Section 2.5.5.

Twin IP Address

: This field displays/sets the redundant twin’s IP address

Twin IP Por

t: This field displays/sets the redundant twin’s IP port

709 Domain

: These fields display the common domain address used for both the IP and LON

709.1 stacks.

Twin IP side Subnet/Node

: This field displays the subnet/node address of the twin’s IP side

709.1 stack.

Twin LON CN side Subnet/Node

: This field displays the subnet/node address of the twin’s LON

component network side 709.1 stack.

Twin Mode ON/OFF

: These radio buttons turn twin mode on or off.

Trigger Twin App Service Pin

: This button propagates a service pin message from the twin

mode monitoring application. This enables remote commissioning of the twin mode

application.

Clear Twin LON CN Config

: This button clears the component network configuration about its

twin from this device’s memory.

Sync Data From Twin

: This button manually requests a sync packet from its twin.

Sync Data To Twin

: This button manually sends a sync packet to its twin.

Submit Changes

: This button updates the configuration memory of the device and refreshes

the web page to reflect any changes.

Содержание eNodeIVTM










































































Результаты поиска

Содержание eNodeIVTM

Отзывы:

Похожие инструкции для eNodeIVTM

Бренды по названию

Популярные бренды

Control Network Solution eNodeIVTM, Руководство пользователя

Результаты поиска

Содержание eNodeIVTM

Отзывы:

Похожие инструкции для eNodeIVTM

Бренды по названию

Популярные бренды