Control Network Solution eNodeIVTM Скачать руководство пользователя

Страница: 42 / 76

September 2011

V1.44

Fig.2.23: Channel List Page in Manual Mode

Channel Address Mode

: Is either

Unicast

Multicast

is only supported in manual

mode. Select the desired mode from the popup menu and click

Submit Change

Multicast IP Addr

: This is the multicast IP address of the router. This is used when the channel

in in

Multicast

mode. Multicast addresses are in the range 224.0.0.0 to 239.255.255.255.

Addresses ending in ".0 " are reserved. Some addresses ending in ".1" are used for multicast

host broadcasts and should also be avoided. Examples of valid multicast addresses include:

225.0.0.2, 225.0.0.3, 225.1.2.3. You may need to check with your network administrator to see

what multicast addresses are available for your use. Enter the desired value and click

Submit

Change

s. The device will have to be rebooted for any Multi-cast addresses changes to take

effect. All devices with same multi-cast address will communicate on port 1628.

Membership List Send

: This button sends a copy of this device's membership list to all the other

devices in the list. When in manual mode a device will accept a membership list from any

device already in its own list. Together with the Membership List Send button, this enables easy

configuration of large manual mode channels without the overhead of a configuration server.

Designate one device as the source of the channel list, (say device A). Enter all the other devices

in Device A's channel list (say B, C, D) for example. No go to each of the other devices and only

Содержание eNodeIVTM










































































Результаты поиска

Содержание eNodeIVTM

Отзывы:

Похожие инструкции для eNodeIVTM

Бренды по названию

Популярные бренды

Control Network Solution eNodeIVTM, Руководство пользователя

Результаты поиска

Содержание eNodeIVTM

Отзывы:

Похожие инструкции для eNodeIVTM

Бренды по названию

Популярные бренды