Control Network Solution eNodeIVTM Скачать руководство пользователя

Страница: 51 / 76

September 2011

V1.44

Side A Serial Transaction Mode

: These radio buttons allow the user to enable or disable Serial

Transaction Mode for Side A. When enabled the Router will send out 852 configuration updates

serially in a round robin fashion to the other 852 devices on the channel instead of in parallel.

This means that an update transaction has to complete or time-out with one device before a

new transaction is started with the next device. This mode significantly reduces bursts of traffic

when devices are added to a channel or their routing data is changed. This may be helpful for

low bandwidth 852 channels. Select the new value and click the

Submit Changes

button.

Side A Serial Transaction Interval

: This field sets the time interval between successive

configuration transactions when Serial Transaction Mode is enabled for Side A. The default is

1000 ms. This enables the user throttle the rate at which configuration updates are sent out on

the channel and thereby manage traffic. This may be helpful for low bandwidth 852 channels.

Enter the new value and click the

Submit Changes

button.

Side A ConfigServer IP Port

: This field appears when the router is in 852 bridge mode and Side

A is in Normal mode. It allows the user to set or change the Side A unicast IP port of the config

server for the Side A 852 channel. To change the port, type in the new port number (0-65535),

and click the

Submit Changes

button.

Side B Mode

: These radio buttons determine the operational mode for Side B, either Manual or

Normal. To change select the appropriate radio button and click the Submit Changes button.

Side B Data IP Port

: This field appears when the router is in 852 bridge mode. It allows the user

to set or change the Side B unicast IP port of the router. To change the port, type in the new

port number (0-65535), and click the

Submit Changes

button.

Side B ConfigServer IP Address

: This field appears only when the router is operating in 852

Bridge mode and Side B is in Normal Mode. This is the unicast IP host address of the

configuration server for the Side B 852 channel. To change the value in the field, type in the

new value in the dotted format

XX.XX.XX.XX

and click the

Submit Changes

button.

Side B ConfigServer IP Port

: This field appears when the router is in 852 bridge mode and Side B

is in Normal mode. It allows the user to set or change the Side B unicast IP port of the config

server for the Side B 852 channel. To change the port, type in the new port number (0-65535),

and click the

Submit Changes

button.

Side B Serial Transaction Mode

: These radio buttons allow the user to enable or disable Serial

Transaction Mode for Side B. When enabled the Router will send out 852 configuration updates

serially in a round robin fashion to the other 852 devices on the channel instead of in parallel.

This means that an update transaction has to complete or time-out with one device before a

new transaction is started with the next device. This mode significantly reduces bursts of traffic

when devices are added to a channel or their routing data is changed. This may be helpful for

low bandwidth 852 channels. Select the new value and click the

Submit Changes

button.

Side B Serial Transaction Interval

: This field sets the time interval between successive

configuration transactions when Serial Transaction Mode is enabled for Side B. The default is

1000 ms this enables the user throttle the rate at which configuration updates are sent out on

Содержание eNodeIVTM










































































Результаты поиска

Содержание eNodeIVTM

Отзывы:

Похожие инструкции для eNodeIVTM

Бренды по названию

Популярные бренды

Control Network Solution eNodeIVTM, Руководство пользователя

Результаты поиска

Содержание eNodeIVTM

Отзывы:

Похожие инструкции для eNodeIVTM

Бренды по названию

Популярные бренды