Control Network Solution eNodeIVTM Скачать руководство пользователя

Страница: 15 / 76

September 2011

V1.44

2. Web Configuration

The Web-based eNodeIV device interface allows the user to access and change configuration

data on the eNodeIV device by using any http Web browser attached to the network. This

allows users to make changes to the eNodeIV device remotely. This chapter familiarises the

user with the various pages of the Web-based Interface and describes the steps necessary to

changing configuration data.

2.1. Default IP Configuration

The eNodeIV device is configured through a web browser such as FireFox, Internet Explorer,

Safari, or others. In order to connect to the eNodeIV device from a web browser, the eNodeIV

device and the computer running the web browser must be connected to the same IP network.

The factory default IP host address of the eNodeIV device is 10.0.2.40 with subnet mask of

255.255.255.0. The router's web server is serving http on port 80. The computer running the

web browser must be able to access the eNodeIV device's subnet.

Default Internet Configuration

IP Host Address

10.0.2.40

IP Subnet Mask

255.255.255.0

Web HTTP Port

2.1.1. Ethernet

For Ethernet equipped eNodeIV devices, first configure the host computer to add an IP

interface on subnet 10.0.2.0/255. Connect one end of a Cat5 Ethernet cable to the RJ-45 on

the eNodeIV device and the other end to an Ethernet hub or switch or directly to a computer

with a crossover cable or straight through if the computer’s Ethernet port supports auto

crossover (Auto MDIX). The eNodeIV Ethernet port is MDI only. In cases where the LAN does

not support the default subnet, a direct connection between the ENodeIV device and the web

browser host computer will be needed.

Содержание eNodeIVTM










































































Результаты поиска

Содержание eNodeIVTM

Отзывы:

Похожие инструкции для eNodeIVTM

Бренды по названию

Популярные бренды

Control Network Solution eNodeIVTM, Руководство пользователя

Результаты поиска

Содержание eNodeIVTM

Отзывы:

Похожие инструкции для eNodeIVTM

Бренды по названию

Популярные бренды