Control Network Solution eNodeIVTM Скачать руководство пользователя

Страница: 68 / 76

September 2011

V1.44

Fig.4.5: Fully Commissioned Router

4.5. NAT Router Example

This section contains step-by-step instructions on how to set up a eNodeIV router for operation

on the LAN side of a NAT router. The NAT support mode enables an eNodeIV device to operate

on the LAN side of a NAT (Network Address Translation) router. The setup is shown in the

following figure.

Fig.4.6: NAT LAN to WAN Architecture

Setup the IP parameters for the eNodeIV as per the

Manual Mode

Normal Mode

instructions above.

Configure the NAT router to port map the 852 port. If you need to access the eNodeIV

web interface from the WAN side then you must also set up and port map the http web

server port for the eNodeIV device.

Enter the static WAN IP address of the NAT router into the NAT

Router WAN Address

field on the eNodeIV device’s

Router Setup Page

Select the radio button to enable NAT support. Click

Submit Changes.

Continue configuring the eNodeIV in either Manual or Normal mode as described in

previous sections.

4.6. DDNS Router Example

The DDNS support mode enables an eNodeIV device to operate on the LAN side of the NAT

(Network Address Translation) router that is also a DDNS client. Routers of this type may have

dynamic IP addresses. Please refer to the figure above for an example of this architecture. This

section contains step-by-step instructions on how to set up an eNodeIV device for operation on

the LAN side of a NAT-DDNS router.

Follow the instructions in the previous section for setting up NAT support with the

Содержание eNodeIVTM










































































Результаты поиска

Содержание eNodeIVTM

Отзывы:

Похожие инструкции для eNodeIVTM

Бренды по названию

Популярные бренды

Control Network Solution eNodeIVTM, Руководство пользователя

Результаты поиска

Содержание eNodeIVTM

Отзывы:

Похожие инструкции для eNodeIVTM

Бренды по названию

Популярные бренды