Control Network Solution eNodeIVTM Скачать руководство пользователя

Страница: 50 / 76

September 2011

V1.44

each of the bridged channels, that is, Side A and Side B.

3.2.1. Router Setup Page

When

852 to 852 Bridging Router Mode is enabled

, the router setup page looks like the

following.

Fig.3.2: Bridging Router Mode Setup Page

Side A Mode

: These radio buttons determine the operational mode for Side A, either Manual or

Normal. To change select the appropriate radio button and click the Submit Changes button.

Side A Data IP Port

: This field appears when the router is in 852 bridge mode. It allows the user

to set or change the Side A unicast IP port of the router. To change the port, type in the new

port number (0-65535), and click the

Submit Changes

button.

Side A ConfigServer IP Address

: This field appears only when the router is operating in 852

Bridge mode and Side A is in Normal Mode. This is the unicast IP host address of the

configuration server for the Side A 852 channel. To change the value in the field, type in the

new value in the dotted format

XX.XX.XX.XX

and click the

Submit Changes

button.

Содержание eNodeIVTM










































































Результаты поиска

Содержание eNodeIVTM

Отзывы:

Похожие инструкции для eNodeIVTM

Бренды по названию

Популярные бренды

Control Network Solution eNodeIVTM, Руководство пользователя

Результаты поиска

Содержание eNodeIVTM

Отзывы:

Похожие инструкции для eNodeIVTM

Бренды по названию

Популярные бренды