Control Network Solution eNodeIVTM Скачать руководство пользователя

Страница: 22 / 76

September 2011

V1.44

parameters will be reset to factory defaults.
7) After about another minute the router will go into reset. This is indicated by the yellow link

light and the green traffic light both going on solid for the Ethernet unit and both going off for

the WiFi unit. Another minute later the router will boot up with all the IP and web parameters

set to factory defaults.
Test the restored IP settings by pinging the default IP address and/or entering the default URL

into a web browser.

2.4. Web Configuration Parameters

In general there are two types of parameters on the following web configuration pages. The

first type take effect immediately upon submission, usually by clicking a submit changes or

other similar button. The other type require the router to be rebooted before taking effect. The

parameters that require a reboot are marked with a green asterisk.
Submit changes will first store the parameters in RAM and then later, in the background, a copy

(actually two copies) will be stored in flash. Power cycling the router before it has time to store

the backup copies in flash means that on the next boot-up it may not retain the changed

parameters. In some cases power cycling or resetting the router while its writing some of the

critical flash parameters may corrupt flash and make the unit inoperable. The Router Setup

page includes a

Prepare to Power Down

button that checks the status of any pending flash

writes and then either displays a page that indicates it is safe to power down or displays a page

with a timer that indicates that one should wait until the timer expires before powering down.

2.5. Status Page

The status page is the home page for the web Tool. The buttons shown on the left will vary

depending on what optional services have been enabled in the router. The Router Status Page

displays basic information about the status of the Router. Changes to the data cannot be made

through this page; it is for information purposes only. Following is a brief description of each

item shown on the page

Содержание eNodeIVTM










































































Результаты поиска

Содержание eNodeIVTM

Отзывы:

Похожие инструкции для eNodeIVTM

Бренды по названию

Популярные бренды

Control Network Solution eNodeIVTM, Руководство пользователя

Результаты поиска

Содержание eNodeIVTM

Отзывы:

Похожие инструкции для eNodeIVTM

Бренды по названию

Популярные бренды