Continental Access SUPERTERM CIC1800 Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 92

Continental Access SUPERTERM CIC1800 Скачать руководство пользователя страница 86

MAINTENANCE

Superterm CIC1800 / CICP1400UL

86

MAINTENANCE

Power Supply Replacement

The following procedure applies after determining
that the Superterm on-board Linear Power Supply
needs replacing.

WARNING
Verify that the AC source voltage is switched off
at the breaker panel before proceeding with
power supply replacement.

1)

Open the Superterm cabinet and locate the
12VDC power supply in the lower right-hand
corner of the cabinet (see Figure 56).

2)

Disconnect the 2-pin Molex connector from the
transformer module's power supply wires (one
black and one white).

3)

Disconnect the RED wire of the 12VDC output
wiring harness from the power input terminal
strip pin 4 (refer to page 12, Step-Down
Transformer Connection for specific
information).

4)

Disconnect the BLACK wire of the 12VDC
output wiring harness from the power input
terminal strip pin 5 (refer to page 12, Step-
Down Transformer Connection, for specific
information).

5)

Remove the two #6-32 nuts securing the power
supply bracket to the Superterm cabinet.

6)

Remove the power supply bracket from the
Superterm cabinet.

7)

Remove the two #6-32 nuts securing the power
supply chassis to the rear wall of the Superterm
cabinet.

8)

Remove the two #6-32 x 1/4" Phillips head
screws securing the power supply chassis to the
bottom of the Superterm cabinet.

9)

Remove the power supply chassis from the
Superterm cabinet.

10)

Install the new power supply in the reverse
order of the removal.

Figure 56 - Superterm Power Supply Replacement

«
...
84
85
86
87
88
...
»

Содержание SUPERTERM CIC1800





























































































Отзывы:

Нет отзывов