Continental Access SUPERTERM CIC1800 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 92

Continental Access SUPERTERM CIC1800 Скачать руководство пользователя страница 22

DOOR CONNECTIONS

Superterm CIC1800 / CICP1400UL

22

Magnetic Stripe Reader Connection

Magnetic Stripe Readers connect to terminal strips
DR1 through DR8 (see Figure 11). Terminal strips
DR I through DR8 follow the same connection
procedures.

Table 8 lists the connections between the DR1
through DR8 terminal strips and the Magnetic
Stripe Reader.

Table 8 - Connection Table for Magnetic Stripe Reader

DRx Terminal Strip

Pin #

Function

1 +5VDC
4 Ground
5 LED
6 Data-1/DAT
7 Data-0/CLK

Magnetic Stripe Reader Cable
Requirements

Magnetic Stripe Readers require a 5-conductor
cable between the Superterm and the particular unit
(see Figure 11).
NOTES: DO NOT use twisted pair cables.

If the Magnetic Stripe Reader does not feature an
LED indicator, substitute with a 4-conductor cable.

Table 9 lists the cable gauge-vs-length
requirements for proper operation of the Superterm
and Magnetic Stripe Readers.

Table 9 - Cable Requirements for Magnetic Stripe

Reader

Unit Distance

Wire

Gauge

Magnetic

Stripe

Reader

(maximum)

1000ft/305m

22AWG Shielded

w/drain

CAUTION
Keep all drain and cable shield wires between the Superterm and Magnetic Stripe Readers short.
Connect drain and cable shield wires to the ground posts located on both sides of Superterm cabinet.
DO NOT ground drain wires and cable shields at any other point.

Figure 11 - Magnetic Stripe Reader Connection to Superterm Board

«
...
20
21
22
23
24
...
»

Содержание SUPERTERM CIC1800





























































































Отзывы:

Нет отзывов