Continental Access SUPERTERM CIC1800 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 92

Continental Access SUPERTERM CIC1800 Скачать руководство пользователя страница 32

RELAY CONNECTIONS

Superterm CIC1800 / CICP1400UL

32

LOCAL Power Door Strike Connection

All door strike relays operating in LOCAL power
mode distribute strike power from the LOCAL
power supply. However, each relay may be
configured in one of two specific ways.

1)

A door strike relay set in a Normally Closed
(NC) configuration holds a door strike circuit
closed until an event triggers the relay and
releases the door strike.

2)

A door strike relay set in a Normally Open
(NO) configuration keeps a door strike circuit
open until an event triggers the relay and
engages the door strike.

NOTE:

Operating the door strike relays with an

emergency sensor requires Normally Closed (NC)
conditions (power is disconnected from the door
strike in emergency situations).

Door Strike Relay Connection - Normally
Open

Table 18 lists the connections between the RLY#x
terminal strip and the associated door strike for a
Normally Open (NO) condition (see Figure 19).

Table 18 - Connection Table for Door Strike

Relay -

Normally Open (NO) Condition

Door Strike Signal

RLY#x Pin

Positive (+)

Pin 1

Common (-)

Pin 2

NOTE:

Operating door strike relays on LOCAL

power requires setting two jumpers per relay.
Refer to page 72, Door Strike Jumper Settings, for
specific information about setting the jumpers.

Door Strike Relay Connection - Normally
Closed

Table 19 lists the connections between the RLY#x
terminal strip and the associated door strike for a
Normally Closed (NC) condition (see Figure 20).

Table 19 - Connection Table for Door Strike

Relay -

Normally Closed (NC) Condition

Door Strike Signal

RLY#x Pin

Positive (+)

Pin 3

Common (-)

Pin 2

NOTE:

Operating door strike relays on LOCAL

power requires setting two jumpers per relay.
Refer to page 72, Door Strike Jumper Settings, for
specific information about setting the jumpers.

«
...
30
31
32
33
34
...
»

Содержание SUPERTERM CIC1800





























































































Отзывы:

Нет отзывов