Continental Access SUPERTERM CIC1800 Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 92

Continental Access SUPERTERM CIC1800 Скачать руководство пользователя страница 72

SETTINGS

Superterm CIC1800 / CICP1400UL

72

SETTINGS

Jumper Settings

The Superterm circuit board functions with a
variety of options. Proper circuit operation
requires setting specific jumpers depending on the
installed access control accessories, the installed
system options, and any network configurations.

232-1 Jumper

The 232-1 jumper enables either the RS-232
communication lines connected to the COM2
terminal strip or the RS-422 communication lines
connected to the XTM terminal strip.

COM2 Enabled

The COM2 port is enabled when the Superterm
uses RS-232 communications protocol.
Connections to the external device are made
through the COM2 terminal strip.



Set the jumper to contact the center post (pin
2) and the left hand post (pin 1) (see Figure
46).

XTM Enabled

The XTM port is enabled when the Superterm
uses RS-422 communications protocol.
Connections to the external device are made
through the XTM terminal strip.



Set the jumper to contact the center post (pin
2) and the right-hand post (pin 3).

EOL1 Jumper

When using the RS-485 communication protocol to
network multiple Superterm units through the
POLL terminal strip, the EOL1 jumper on the
LAST unit in the communication network must be
set to the TERMINATED position.

Superterm

TERMINATED

Set the jumper to contact the center post (pin 2)
and the left hand post (pin 1) (see Figure 46).

Superterm

NOT TERMINATED

Set the jumper to contacting the center post (pin
2) and the right-hand post (pin 3).

EOL2 Jumper

When operating multiple Superterm units in a
MULTIDROP RS-422 network, the EOL2 jumper
on the LAST unit in the communication network
must be set to the TERMINATED position.

NOTE: When operating multiple Superterm units
in a REPEAT RS-422 network, the EOL2 jumper
on

every

Superterm unit must be set to the

TERMINATED position.

Superterm

TERMINATED

Set the jumper to contact the center post (pin 2)
and the left hand post (pin 1) (see Figure 46).

Superterm

NOT TERMINATED

Set the jumper to contact the center post (pin 2)
and the right-hand post (pin 3).

«
...
70
71
72
73
74
...
»

Содержание SUPERTERM CIC1800





























































































Отзывы:

Нет отзывов