Continental Access SUPERTERM CIC1800 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 92

Continental Access SUPERTERM CIC1800 Скачать руководство пользователя страница 14

INSTALLATION

Superterm CIC1800 / CICP1400UL

14

Cabinet Mounting

Inspect the mounting surface around the proposed
installation site. The mounting surface must be
capable of supporting 55 pounds (25Kg) plus any
additional weight of the installation hardware.

CAUTION
Use only suitable mounting hardware for the
type of wall construction encountered.

1.

Determine the Superterm cabinet mounting
location.

2.

Mark the four mounting holes against the
mounting surface using the Superterm cabinet
as a template or using the measurements
provided in Figure 4.

NOTE: Mark the small oval portion of the cabinet
screw holes (see Figure 5, Detail A).

3.

Place the Superterm cabinet out of the way.

4.

Drill pilot holes to the required depth and size
for the mounting screws.

5.

Insert the mounting screws into the wall.
Leave approximately one quarter of the screw's
length protruding from the wall.

NOTE: Do not tighten screws completely at this
time.

6.

Place the Superterm cabinet over the mounting
screws.

7.

Secure the Superterm cabinet to the mounting
surface and tighten the remaining length of the
screws.

Secure the Superterm cabinet to the mounting
surface using the two lower screws, and then
tighten the remaining length of the screws.

Note:

Use all 4 mounting screws to secure

cabinet to wall. For mounting to 3/4" thick
plywood, use four minimum 1/4" x 3/4" wood
screws. For mounting to sheetrock, use four
minimum 1/4" toggle bolts.

Figure 4 - Superterm Cabinet Mounting Hole
Dimensions

Figure 5 - Superterm Mounting Screws

«
...
12
13
14
15
16
...
»

Содержание SUPERTERM CIC1800





























































































Отзывы:

Нет отзывов