Comtech EF Data SDM-9000 Скачать руководство пользователя страница 245 | Manualshive

Страница: 245 / 256

background image

SDM-9000 Satellite Modem

Remote Control Operation

Rev. 4

B–27

Bulk
Consol.
Status
Faults

Command
:
Response:

<add/BCSF_'cr'
>add/BCSF_abcdefghijklmno'cr''l
f']

This command causes all modem fault status to be returned. To
reduce the length of the response, fault status is embedded into
the bit structure of the characters that are returned. Faults are
indicated by a binary 1 in the designated bit position.

Where: Character 'a': Modulator fault status character 1.

Bit 6 = 1 always.
Bit 5 = Modulator module fault.
Bit 4 = RF output status actual, not programmed status (1 =
ON, 0 = OFF).
Bit 3 through Bit 0 = Binary representation (0 to 10) of the
number of modulator stored faults.

Where: Character 'b': Modulator fault status character 2.

Bit 6 = 1 always.
Bit 5 = IF Synthesizer.
Bit 4 = Data Clock Activity.
Bit 3 = Data Clock Synthesizer.
Bit 2 = I Channel.
Bit 1 = Q Channel.
Bit 0 = AGC Level.

Where: Character 'c': Modulator fault status character 3.

Bit 6 = 1 always.
Bit 5 = Internal SCT Synthesizer.
Bit 4 = Programming.
Bit 3 = Configuration.
Bit 2 = External Reference Activity.
Bit 1 = reserved.
Bit 0 = reserved.

Where: Character 'd': Demodulator fault status character 1.

Bit 6 = 1 always.
Bit 5 = Demod module fault.
Bit 4 = Carrier detect status (0 for decoder lock).
Bit 3 through Bit 0 = Binary representation (0 to 10) of the
number of demodulator stored faults.

Where: Character 'e': Demodulator fault status character 2.

Bit 6 = 1 always.
Bit 5 = IF Synthesizer Lock.
Bit 4 = Receive Clock Synthesizer.
Bit 3 = I Channel.
Bit 2 = Q Channel.
Bit 1 = Descrambler.
Bit 0 = BER threshold.

Where: Character 'f': Demodulator fault status character 3.

Bit 6 = 1 always.
Bit 5 = Programming.
Bit 4 = Configuration.
Bit 3 = reserved.
Bit 2 = reserved.
Bit 1 = reserved.
Bit 0 = reserved.

Where: Character 'g': Interface transmit side faults character 1.

Bit 6 = 1 always.
Bit 5 = reserved.
Bit 4 = reserved.
Bit 3 through Bit 0 = Binary representation (0 to 10) of the
number of interface transmit side stored faults.

Where: Character 'h': Interface transmit side faults character 2.

«
...
243
244
245
246
247
...
»

Содержание SDM-9000

































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SDM-9000

Interactive DDM3500

Бренд: Ubee Страницы: 21

Бренд: i-mate Страницы: 7

Бренд: Linksys Страницы: 4

Бренд: RCA Страницы: 21

CellPipe IAD 4A

Бренд: Lucent Technologies Страницы: 28

Бренд: Bay Technical Associates Страницы: 27

Comtrend CT-6382T

Бренд: Teleconnect Страницы: 6

Gigaset SE680 WiMAX

Бренд: Gigaset Страницы: 62

Gigaset SE587 WLAN dsl

Бренд: Gigaset Страницы: 89

FRITZ!Box 6660 Cable

Бренд: Fritz! Страницы: 281

JUPITER System HT2000

Бренд: Hughes Страницы: 31

Бренд: DOUXE Страницы: 9

Бренд: MTX Страницы: 46

Бренд: Campbell Страницы: 22

Бренд: Zte Страницы: 24

Бренд: Hama Страницы: 2

Бренд: Raveon Страницы: 13

Бренд: Eminent Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды