Comtech EF Data SDM-9000 Скачать руководство пользователя страница 45

Страница: 45 / 256

SDM-9000 Satellite Modem

Installation

Rev. 4

2–3

2.3 System Installation

Install the modem as follows:

1. Mount the modem chassis in the assigned position of the equipment rack. It is

recommended that the modem be supported by a rack-mounted shelf, or the two
rear rack-mount brackets supplied with the unit.

Note:

For a custom rack installation, refer to the chassis dimensional drawing in

Figure 2-1.

2. Connect the cables to the proper locations on the rear panel. Refer to Section 2.4

for connector pinouts, placement, and functions.

3. Open the front panel and install the three main PCB assemblies (Figure 1-2) as

follows:

Install the modulator PCB (AS/3969) in the top slot.

Install the interface PCB (AS/3971, AS/4477, or AS/5618) in the middle
slot.

Install the demodulator PCB (AS/3970) in the bottom slot.

Note:

The cards are keyed, and will only fit in the proper chassis slot. Verify

the PCBs are properly seated.

Before turning on the power switch, verify all interface jumper settings are in
their proper positions (Chapter 3), and become familiar with front panel
operation (Chapter 4).

Turn on the power switch (located inside the front panel).

Check for the proper TX output signal level and spectrum.

Check for the proper RX input signal level and spectrum.

8. If there is any installation problem, refer to Chapter 6 for troubleshooting

assistance.

Содержание SDM-9000

































































































































































































































































Результаты поиска

Содержание SDM-9000

Отзывы:

Похожие инструкции для SDM-9000

Бренды по названию

Популярные бренды

Comtech EF Data SDM-9000, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SDM-9000

Отзывы:

Похожие инструкции для SDM-9000

Бренды по названию

Популярные бренды