Comtech EF Data SDM-9000 Скачать руководство пользователя страница 100

Страница: 100 / 256

Operation

SDM-9000 Satellite Modem

4–26

Rev. 4

4.2.3.2 Demodulator Faults

CARRIER DETECT

Carrier detect fault.

Indicates the decoder is not locked.

IF SYNTHESIZER

Demodulator IF synthesizer fault.

Indicates the IF synthesizer is not locked.

RX CLOCK SYN

RX data clock synthesizer fault.

Indicates a loss of lock on the reference of the demodulator clock
recovery oscillator.

I CHANNEL

I channel activity fault.

Indicates a loss of activity in the I channel of the quadrature
demodulator.

Q CHANNEL

Q channel activity fault.

Indicates a loss of activity in the Q channel of the quadrature
demodulator.

DESCRAMBLER

Descrambler activity alarm.

Indicates a loss of activity in the descrambler.

BER THRESHOLD

BER threshold set in the Configuration Demod menu.

MODULE

Demodulator/decoder module fault.

Typically indicates that the Demod/decoder module is missing or will
not program.

PROGRAMMING

Demodulator programming fault.

CONFIGURATION

Demodulator configuration fault.

Indicates the demodulator cannot execute a programmed
configuration parameter.

Содержание SDM-9000

































































































































































































































































Результаты поиска

Содержание SDM-9000

Отзывы:

Похожие инструкции для SDM-9000

Бренды по названию

Популярные бренды

Comtech EF Data SDM-9000, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SDM-9000

Отзывы:

Похожие инструкции для SDM-9000

Бренды по названию

Популярные бренды