Comtech EF Data SDM-9000 Скачать руководство пользователя страница 10

Страница: 10 / 256

Rev. 4

Customer Support

Contact the Comtech EFData Customer Support Department for:

•

Product support or training

•

Information on upgrading or returning a product

•

Reporting comments or suggestions concerning manuals

A Customer Support representative may be reached at:

Comtech EFData
Attention: Customer Support Department
2114 West 7th Street
Tempe, Arizona 85281 USA

(480) 333-2200 (Main Comtech EFData Number)
(480) 333-4357 (Customer Support Desk)
(480) 333-2161 FAX

or, E-Mail can be sent to the Customer Support Department at:

[email protected]

www.comtechefdata.com

To return a Comtech EFData product (in-warranty and out-of-warranty) for
repair or replacement:

Request a Return Material Authorization (RMA) number from the Comtech
EFData Customer Support Department.

Be prepared to supply the Customer Support representative with the model
number, serial number, and a description of the problem.

To ensure that the product is not damaged during shipping, pack the product in
its original shipping carton/packaging.

Ship the product back to Comtech EFData. (Shipping charges should be prepaid.)

For more information regarding the warranty policies, see Warranty Policy, p. xiv.

Содержание SDM-9000

































































































































































































































































Результаты поиска

Содержание SDM-9000

Отзывы:

Похожие инструкции для SDM-9000

Бренды по названию

Популярные бренды

Comtech EF Data SDM-9000, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SDM-9000

Отзывы:

Похожие инструкции для SDM-9000

Бренды по названию

Популярные бренды