Comtech EF Data SDM-9000 Скачать руководство пользователя страница 69

Страница: 69 / 256

SDM-9000 Satellite Modem

Configuration

Rev.4

3–11

3.5.2.2 Tools Required

The following tool is required to accomplish the task of this section:

Tool

Description

Driver, Nut

1/4-inch

3.5.2.3 Installation Procedure

Note:

The Nyquist filter PCB is field-replaceable to enable the user to install optional

data rates.

1. Install the Nyquist filter PCB as a daughter card on the modulator or

demodulator PCB as follows:

Type

Part Number

Used with

TX PCB

AS/4124-1

Baseband Modulator PCB (AS/3969)

RX PCB

AS/4124-2

Baseband Demodulator PCB (AS/3970)

Ensure that each filter has three 10-pin connectors for I/O and power.

Mount the card on the four standoffs with a 1/4” hex nut on each standoff to
secure the PCB. Tighten each nut using the 1/4” nut driver.

2. Refer to Figure 3-7 for connector locations.

3.5.2.3.1 Nyquist Filter Removal

1. Remove the TX filter (AS/4124-1) or RX filter (AS/4124-2) as follows:

Open the modem front door and turn off the power.

b. Remove the modulator or demodulator PCB from the modem and place on a

static-free work area.

Remove the four 1/4” hex nuts that secure the filter card (AS/4124-X) using
the 1/4” nut driver.

Note:

Do not remove the screws and standoffs from the modulator or

demodulator. Remove the four hex nuts only.

2. Carefully unplug the filter card from the modulator or demodulator connectors.

Содержание SDM-9000

































































































































































































































































Результаты поиска

Содержание SDM-9000

Отзывы:

Похожие инструкции для SDM-9000

Бренды по названию

Популярные бренды

Comtech EF Data SDM-9000, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SDM-9000

Отзывы:

Похожие инструкции для SDM-9000

Бренды по названию

Популярные бренды