Comtech EF Data SDM-9000 Скачать руководство пользователя страница 183 | Manualshive

Страница: 183 / 256

background image

SDM-9000 Satellite Modem

Maintenance

Rev. 4

6–25

6.2.2.2.5 Common Equipment Faults

Fault/Alarm

Possible Problem and Action

BATTERY/CLOCK

M&C battery voltage or clock fault.

Indicates a low voltage in the memory battery. Typically this will be
active when a modem has been hard reset, the firmware has been
changed, and the modem is first turned on. If the fault occurs without
a firmware change or hard reset of the modem, replace the
display/M&C card.

-12 VOLT SUPPLY

-12 VDC power supply fault.

Indicates a high or low voltage condition. Level is

±

5%. Check for a

short on the -12 VDC line from the power supply or on any of the
plug-in boards. Check TP2 on the display/M&C card to verify the
proper -12 VDC monitor voltage (1.06 VDC). If this voltage is not
correct, it will verify that the -12 VDC supply is not at the proper level.
Try isolating the fault to a single board. If removing each of the
boards does not fix the problem, then the power supply is faulted.
Return the faulty plug-in board or replace the chassis power supply.

+12 VOLT SUPPLY

+12 VDC power supply fault.

Use the same procedure as with -12V fault. To verify the +12 VDC
power supply voltage, check TP4 on the display/M&C card. A
voltage of 3.81 VDC will be monitored when the +12 VDC is at the
proper level.

+5 VOLT SUPPLY

+5 VDC power supply fault.

Use the same procedure as with a -12 VDC fault. The +5 VDC
supply requires a minimum load of 1A. This is accomplished with the
display/M&C card and one other card being plugged into the
chassis. To verify the +5 VDC power supply voltage, check TP5 on
the display/M&C card. A voltage of 2.5 VDC will be monitored when
the +5 VDC is at the proper level.

-5 VOLT SUPPLY

-5 VDC power supply fault.

To verify the -5 VDC power supply voltage, check TP3 on the
display/M&C card. A voltage of 2.03 VDC will be monitored when the
-5 VDC is at the proper level.

CONTROLLER

Controller fault.

Indicates a loss of power in the M&C card. Typically indicates the
controller has gone through a power on-off cycle.

INTERFACE

Interface module fault.

Indicates a problem in programming the interface card. Ensure the
interface card is present and properly seated. If the card is properly
seated, this could indicate a problem in the M&C card or in the
interface between the interface card and M&C card. Return the
defective card for repair.

«
...
181
182
183
184
185
...
»

Содержание SDM-9000

































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SDM-9000

Бренд: RACOM Страницы: 56

Бренд: Campbell Страницы: 14

MO128 - QUICK_START_GUIDE

Бренд: SWEEX Страницы: 9

Бренд: Data-Linc Group Страницы: 15

Бренд: Multitech Страницы: 90

MultiModem MT2834ZDX Series

Бренд: Multitech Страницы: 8

Бренд: Ebyte Страницы: 42

Бренд: Haier Страницы: 24

Бренд: Haier Страницы: 23

Бренд: GDI Страницы: 49

Бренд: Zte Страницы: 2

Бренд: Zte Страницы: 12

Бренд: Zte Страницы: 8

Бренд: Option Wireless Technology Страницы: 16

Бренд: Hughes Network Страницы: 63

Бренд: ADTRAN Страницы: 4

Бренд: ADTRAN Страницы: 80

Бренд: Paradyne Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды