Comtech EF Data SDM-9000 Скачать руководство пользователя страница 243

Страница: 243 / 256

SDM-9000 Satellite Modem

Remote Control Operation

Rev. 4

B–25

Bulk Consol.
Status
(continued)

Parameter

Number

Parameter Name

(Command Reference)

Description

Descrambler enable

(ref. 'DE_' command).

Buffer clock source

(ref. 'BC_' command).

Interface buffer size

(ref. 'IBS_' command).

Interface transmit overhead type

(ref. 'ITOT_' command).

Interface receive overhead type

(ref. 'IROT_' command).

Interface substitution pattern

(ref. 'ISP_' command).

Interface read error

(ref. 'IRE_' command).

Transmit data fault

(ref. 'TDF_' command).

Receive data fault

(ref. 'RDF_' command).

Interface service channel TX1

(ref. 'ISCL_' command).

Interface service channel TX2

(ref. 'ISCL_' command).

Interface service channel RX1

(ref. 'ISCL_' command).

Interface service channel RX2

(ref. 'ISCL_' command).

Transmit data phase

(ref. 'TDP_' command).

Receive data phase

(ref. 'RDP_' command).

Backward Alarm enable TX1

(ref. 'BW_TX1_' command).

Backward Alarm enable TX2

(ref. 'BW_TX2_' command).

Backward Alarm enable TX3

(ref. 'BW_TX3_' command).

Backward Alarm enable TX4

(ref. 'BW_TX4_' command).

Backward Alarm enable RX1

(ref. 'BW_RX1_' command).

p36 = n, where 'n' is '0' (OFF) or '1' (ON).

p37 = n, where 'n' is '0' (INT), '1' (REF), '2' (EXT), '3' (SAT), or
'4' (HS).

p38 = nn, buffer size in milli-seconds.

p39 = n, where 'n' is '0' (NONE) or '1' (IDR).

p40 = n, where 'n' '0' (NONE) or '1' (IDR).

p41 = n, where 'n' is '0' (OFF) or '1' (ON).

p42 = n, where 'n' is '0' (FRM/OFF) or '1' (2047/ON).

p43 = n, where 'n' is '0' (NONE), '1' (DATA), or '2' (AIS).

p44 = n, where 'n' is '0' (NONE), '1' (DATA), or '2' (AIS).

p45 = nnn, service channel level in dBm.

p46 = nnn, service channel level in dBm.

p47 = nnn, service channel level in dBm.

p48 = nnn, service channel level in dBm.

p49 = n, where 'n' is '0' (NRM) or '1' (INV).

p50 = n, where 'n' is '0' (NRM) or '1' (INV).

p51 = n, where 'n' is '0' (OFF) or '1' (ON).

p52 = n, where 'n' is '0' (OFF) or '1' (ON).

p53 = n, where 'n' is '0' (OFF) or '1' (ON).

p54 = n, where 'n' is '0' (OFF) or '1' (ON).

p55 = n, where 'n' is '0' (OFF) or '1' (ON).

Содержание SDM-9000

































































































































































































































































Результаты поиска

Содержание SDM-9000

Отзывы:

Похожие инструкции для SDM-9000

Бренды по названию

Популярные бренды

Comtech EF Data SDM-9000, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SDM-9000

Отзывы:

Похожие инструкции для SDM-9000

Бренды по названию

Популярные бренды