Comtech EF Data SDM-9000 Скачать руководство пользователя страница 105

Страница: 105 / 256

Operation

SDM-9000 Satellite Modem

4–32

Rev. 4

SDM-9000 "TYPE"

VER: 6.1.1

FUNCTION SELECT

STORED

FLTS/ALMS

MODULATOR X

DEMODULATOR X

TX INTERFACE X

RX INTERFACE X

COMMON X

BACKWARD ALARMS

HH:MM:SS/MM-DD-YY

(FAULT LABEL)

IF SYNTHESIZER

DATA CLOCK ACT
DATA CLOCK SYN

I CHANNEL

Q CHANNEL

AGC

INTERNAL SCT SYN

EXT REF ACT

MODULE

PROGRAMMING

CONFIGURATION

See notes.

HH:MM:SS/MM-DD-YY

(FAULT LABEL)

CARRIER DETECT

IF SYNTHESIZER

RX CLOCK SYN

I CHANNEL

Q CHANNEL

DESCRAMBLER

BER THRESHOLD

MODULE

PROGRAMMING

CONFIGURATION

See notes.

HH:MM:SS/MM-DD-YY

(FAULT LABEL)

TX DATA/AIS

TX CLK PLL

TX CLK ACTIVITY

PROGRAMMING

CONFIGURATION

See notes.

HH:MM:SS/MM-DD-YY

(FAULT LABEL)

BUFFER UNDERFLOW

BUFFER OVERFLOW

RX DATA/AIS

FRAME BER

BUFFER CLK PLL

BUFFER CLK ACT

DEMUX LOCK

RX 2047 LOCK

BUFFER FULL

PROGRAMMING

CONFIGURATION

See notes.

HH:MM:SS/MM-DD-YY

(FAULT LABEL)

BATTERY/CLOCK

-12 VOLT SUPPLY

+12 VOLT SUPPLY

+5 VOLT SUPPLY

-5 VOLT SUPPLY

CONTROLLER

INTERFACE MODULE

See notes.

HH:MM:SS/MM-DD-YY

(FAULT LABEL)

BW ALARM RX #4
BW ALARM RX #3
BW ALARM RX #2
BW ALARM RX #1
BW ALARM TX #4
BW ALARM TX #3
BW ALARM TX #2
BW ALARM TX #1

See notes.

IDR overhead only.

Notes:

1. X = 0 to 9

2. Stored time/date will alternate.
HH:MM:SS, MM-DD-YY, or no fault.

UNAVAL SECONDS X

HH:MM:SS/MM-DD-YY

See notes.

Reed-Solomon only.

CLEAR??

Press [ENTER] to clear stored

faults.

ACCESS TO

SUBMENU

CONDITIONAL OR

OPTION-DEPENDENT

Parameter Information

Key:

Figure 4-10. Stored Faults/Alarms Menu

Содержание SDM-9000

































































































































































































































































Результаты поиска

Содержание SDM-9000

Отзывы:

Похожие инструкции для SDM-9000

Бренды по названию

Популярные бренды

Comtech EF Data SDM-9000, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SDM-9000

Отзывы:

Похожие инструкции для SDM-9000

Бренды по названию

Популярные бренды