Comtech EF Data SDM-9000 Скачать руководство пользователя страница 236

Страница: 236 / 256

Remote Control Operation

SDM-9000 Satellite Modem

B–18

Rev. 4

Demodulato
r Rate
Status

Command:
Response:

<add/DR_'cr'
>add/DR_nnnn_mmmm.mmm'cr''lf']

Where:

nnnnn = One of the following decoder rates:

1/2 (QPSK 1/2)
3/4 (QPSK 3/4)
7/8 (QPSK 7/8)
16Q34 (16QAM 3/4)
16Q78 (16QAM 7/8)
8P23 (8PSK 2/3)
8P56 (8PSK 5/6)
N/A (Not Assigned)

mmmmm.mmm = Data rate in kHz.

Receive
Signal Level
Status

Command:
Response:

<add/RSL_'cr'
>add/RSL_xsnndBm'cr''lf']

Where:

x = < or > (data modifier to indicate that the receive
signal level is less than or greater than the returned
value).

s = + or - (receive signal level sign, plus or minus).

nn = 0 to 99 (receive signal level magnitude).

Notes:

1. The 'x' (< or >) parameter is only returned if the

level has exceeded the computational resolution of
the system.

2. 'No Data' is returned if the level cannot be

calculated.

3. 'Sampling' is returned if not enough data is currently

available to calculate the level.

Interface
Buffer Fill
Status

Command:
Response:

<add/IBFS_'cr'
>add/IBFS_nn%'cr''lf']

Where: nn = 1 to 99 (relative to buffer depth).

Current
Sweep
Value

Command:
Response:

<add/CSV_'cr'
>add/CSV_snnnnn'cr'
CD_xxx'cr''lf']

Where:

s = + or - (sweep offset from center).
nnnnn = 0 to 60000.
xxx = OK or FLT (decoder lock status OK or FAULT).

This command returns the current sweep value and the
decoder lock status.

Содержание SDM-9000

































































































































































































































































Результаты поиска

Содержание SDM-9000

Отзывы:

Похожие инструкции для SDM-9000

Бренды по названию

Популярные бренды

Comtech EF Data SDM-9000, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SDM-9000

Отзывы:

Похожие инструкции для SDM-9000

Бренды по названию

Популярные бренды