Comtech EF Data SDM-9000 Скачать руководство пользователя страница 115

Страница: 115 / 256

Operation

SDM-9000 Satellite Modem

4–42

Rev. 4

4.2.5.3 Utility Interface

TX OVERHEAD TYPE

Select IDR or None for TX overhead type.

Note:

The ESC option must be installed.

RX OVERHEAD TYPE

Select IDR or None for RX overhead type.

Note:

The ESC option must be installed.

TERRESTRIAL INTF

Displays the following interface type:

•

G.703

•

ECL

•

PECL

•

MIL-STD-188

INTERFACE BUILD

Displays the interface module type (1, 2, or 3). This menu is a
status-only window reporting the following four types of modem
operation:

•

Type

Base

•

Type 2

Doppler Buffer

•

Type 3

Doppler Buffer and ESC

INTERFACE OPTION

This menu is a status-only window reporting the interface
options. The interface module options displayed are:

•

Buffer

•

ESC

•

(EFD)

•

(DVB)

•

ESC-64K

TX INTERFACE ESC

This menu is a status-only window reporting the status of the
ESC interface. The TX options displayed are:

•

64K

Data

•

2-32K

Audio

RX INTERFACE ESC

This menu is a status-only window reporting the status of the
ESC interface. The RX options displayed are:

•

64K

Data

•

2-32K

Audio

TX DATA PHASE

Allows the user to invert TX data coming from the terrestrial
network.

On entry, press [

←

] or [

→

] to select Normal or Inverted. Press

[ENTER] to execute the change.

Note:

This menu is only available for the ECL, PECL, or

MIL-STD-188 interface.

Содержание SDM-9000

































































































































































































































































Результаты поиска

Содержание SDM-9000

Отзывы:

Похожие инструкции для SDM-9000

Бренды по названию

Популярные бренды

Comtech EF Data SDM-9000, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SDM-9000

Отзывы:

Похожие инструкции для SDM-9000

Бренды по названию

Популярные бренды