Comtech EF Data SDM-9000 Скачать руководство пользователя страница 246 | Manualshive

Страница: 246 / 256

background image

Remote Control Operation

SDM-9000 Satellite Modem

B–28

Rev. 4

Bit 6 = 1 always.
Bit 5 = Transmit Data/AIS.
Bit 4 = Transmit Synthesizer PLL Lock.
Bit 3 = Selected Transmit Clock Activity.
Bit 2 = Programming.
Bit 1 = Configuration.
Bit 0 = reserved.

Where: Character 'i': Interface receive side faults character 1.

Bit 6 = 1 always.
Bit 5 = reserved.
Bit 4 = reserved.
Bit 3 through Bit 0 = Binary representation (0 to 10) of the
number of interface receive side stored faults.

Where: Character 'j': Interface receive side faults character 2.

Bit 6 = 1 always.
Bit 5 = Buffer Underflow.
Bit 4 = Buffer Overflow.
Bit 3 = Receive Data Loss/AIS.
Bit 2 = Frame BER.
Bit 1 = reserved.
Bit 0 = Selected Buffer Clock Activity.

Where: Character 'k': Interface receive side faults character 3.

Bit 6 = 1 always.
Bit 5 = Buffer Clock PLL Lock.
Bit 4 = Demux Lock.
Bit 3 = 2047 Pattern Lock Detect.
Bit 2 = Buffer Full.
Bit 1 = Programming.
Bit 0 = Configuration.

Where: Character 'l': Common equipment fault status character
1.

Bit 6 = 1 always.
Bit 5 = Monitor and Control Module.
Bit 4 = Interface Module.
Bit 3 through Bit 0 = Binary representation (0 to 10) of the
number of common equipment stored faults.

Where: Character 'm': Common equipment fault status character
2.

Bit 6 = 1 always.
Bit 5 = Battery/Clock.
Bit 4 = +5V Power Supply.
Bit 3 = -5V Power Supply.
Bit 2 = +12V Power Supply.
Bit 1 = -12V Power Supply.
Bit 0 = reserved.

Where: Character 'n': Interface backward alarm status character
1.

Bit 6 = 1 always.
Bit 5 = TX Backward Alarm 1.
Bit 4 = TX Backward Alarm 2.
Bit 3 through Bit 0 = Binary representation (0 to 10) of the
number of backward alarm stored faults.

Where: Character 'o': Interface backward alarm status character
2.

Bit 6 = 1 always.
Bit 5 = TX Backward Alarm 3.
Bit 4 = TX Backward Alarm 4.
Bit 3 = RX Backward Alarm 1.
Bit 2 = RX Backward Alarm 2.
Bit 1 = RX Backward Alarm 3.
Bit 0 = RX Backward Alarm 4.

«
...
244
245
246
247
248
...
»

Содержание SDM-9000

































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SDM-9000

NetLink 1082/144

Бренд: Patton electronics Страницы: 32

Бренд: TC Communications Страницы: 6

eSAM ITRON FC200

Бренд: Intercel Страницы: 12

Бренд: Nokia Страницы: 10

Бренд: Kathrein Страницы: 16

Бренд: Zoom Страницы: 2

Бренд: Paradyne Страницы: 1

Бренд: Ebyte Страницы: 17

Бренд: Ebyte Страницы: 24

Бренд: Ebyte Страницы: 35

Бренд: Ebyte Страницы: 35

Бренд: Pantech Страницы: 118

Бренд: Spectrum Страницы: 7

Бренд: Spectrum Страницы: 6

Бренд: Tait Страницы: 30

Бренд: NETGEAR Страницы: 2

EtherLink 3C900B

Бренд: 3Com Страницы: 154

Бренд: ICPDAS Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды