manualshive.com logo in svg

CommScope Ruckus ICX 7750, Руководство по установке оборудования

Поделиться
Скачать
CommScope Ruckus ICX 7750 Скачать руководство пользователя страница 55

Ruckus ICX 7750 Switch Hardware Installation Guide 

53

Part Number: 53-1003900-10

Ruckus ICX 7750 Operation

Ruckus ICX 7750 front-panel LEDs

 

FIGURE 39

Ruckus ICX 7750-48C front-panel LEDs

The Ruckus ICX 7750-48F has the following LEDs on the front panel:

•

Two power supply unit (PSU) bicolor status LEDs (green and amber) labeled PSU1 and PSU2

•

One DIAG LED bicolor status LED (green and amber)

•

One MS LED bicolor status LED (green and amber)

•

One HA LED bicolor status LED (green and amber)

•

One RDNT LED bicolor status LED (green and amber)

•

48 1/10 GbE SFP+ port bicolor status LEDs (green for 10 GbE and amber for 1 GbE) that indicate the 1 GbE or 10 GbE mode 
of operation

•

Four bicolor status LEDs (green and amber) for each of the six QSFP+ ports that indicate the status of the ports in 40 GbE mode 
and 4x10 GbE breakout mode

Figure 40

 shows the LEDs on the Ruckus ICX 7750-48F front panel.

The up-arrow port status LEDs for the 10 GbE ports correspond to the upper, odd-numbered ports; the down-arrow port status LEDs 
correspond to the lower, even-numbered ports.

1

Upper 1/10 GbE port LEDs

4

MS and DIAG status LEDs

2

Lower 1/10 GbE port LEDs

5

HA and RDNT status LEDs

3

PSU1 and PSU2 status LEDs 
(PSU1 corresponds to the right power supply slot 
on the rear panel and PSU2 corresponds to the left 
power supply slot, as viewed from the rear)

Содержание Ruckus ICX 7750




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды