manualshive.com logo in svg

CommScope Ruckus ICX 7750, Руководство по установке оборудования

Поделиться
Скачать
CommScope Ruckus ICX 7750 Скачать руководство пользователя страница 25

Ruckus ICX 7750 Switch Hardware Installation Guide 

23

Part Number: 53-1003900-10

Installing the Ruckus ICX 7750

Installation precautions

 

Lifting precautions

Power precautions

DC-DC power source cautions

DANGER

Make sure the rack housing the device is adequately secured to prevent it from becoming unstable or falling over.

CAUTION

Use a separate branch circuit for each AC power cord, which provides redundancy in case one of the circuits fails.

DANGER

To avoid high voltage shock, do not open the device while the power is on.

CAUTION

Ensure that the device does not overload the power circuits, wiring, and over-current protection. To determine the possibility 
of overloading the supply circuits, add the ampere (amp) ratings of all devices installed on the same circuit as the device. 
Compare this total with the rating limit fo the circuit. The maximum ampere ratings are usually printed on the devices near the 
input power connectors.

DANGER

Disconnect the power cord from all power sources to completely remove power from the device.

CAUTION

Before plugging a cable to any port, be sure to discharge any static charge stored on the cable by touching the electrical 
contacts to ground surface.

CAUTION

If the installation requires a different power cord than the one supplied with the device, make sure you use a power cord 
displaying the mark of the safety agency that defines the regulations for power cords in your country. The mark is your 
assurance that the power cord can be used safely with the device.

CAUTION

For DC systems, use grounding wire of at least 12 American Wire Gauge (AWG). The grounding wire should be attached to 
the DC input connector (as shown in 

Figure 30

); the other end connects to the building ground.

CAUTION

For the DC input circuit to the system, make sure there is a 20 Amp circuit breaker, minimum 60 VDC, double pole, on the 
input terminal block to the power supply. The input wiring for connection to the product should be copper wire, 12 AWG, 
marked VW-1, and rated minimum 90°C.

Содержание Ruckus ICX 7750




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды