manualshive.com logo in svg

CommScope Ruckus ICX 7750, Руководство по установке оборудования

Поделиться
Скачать
CommScope Ruckus ICX 7750 Скачать руководство пользователя страница 67

Ruckus ICX 7750 Switch Hardware Installation Guide 

65

Part Number: 53-1003900-10

Managing the Ruckus ICX 7750

Replacing fan trays

 

9.

When you are sure the power supply has properly engaged the connector, tighten the retainer screws to secure the power supply 
in the slot.

10. Plug the power cord into the power supply to power on the unit.

The power supply will immediately attempt to power up.

11. Verify that the LED on the new power supply displays steady green while the Ruckus ICX 7750 is operating. If the LED is not 

steady green, ensure that the power supply is securely installed and seated properly. Alternatively, check the PSU1 and PSU2 
LEDs on the switch front panel (refer to 

“LED patterns”

 on page 55).

You can enter the 

show chassis

 command at the command line prompt to display power supply status.

Replacing fan trays

The Ruckus ICX 7750 includes four redundant, hot-swappable fan units. However, it can run on one power supply and three fans. In that 
case, the empty power supply and fan slot must be covered using the filler panels.

NOTE

Maintain all power supply and fan trays in operational condition to provide redundancy.

NOTE

Disassembling any part of the power supply and fan tray voids the warranty and regulatory certifications. There are no 
user-serviceable parts inside the power supply and fan tray.

Determining the need to replace a fan tray

Enter the 

show chassis

 command in the command line interface to display fan status.

Time and items required

Replacing a fan tray in the Ruckus ICX 7750 should take less than two minutes to complete.

You need the following items to replace a fan tray in the Ruckus ICX 7750:

•

A new fan tray (must have the same part number and the same airflow label as the fan tray being replaced; refer to 

Figure 42

 on 

page 63 for the location of the airflow label)

•

A #1 Phillips screwdriver

Installing or replacing the fan tray

Complete the following steps to install or replace a fan tray in a Ruckus ICX 7750.

CAUTION

For the Ruckus ICX 7750 devices, be sure that the airflow direction of the fan tray matches thatof the installed power supply 
unit. The power supplies and fan trays are clearly labeled with either a green arrow with an “E”, or an orange arrow with an “I.”

CAUTION

Because the cooling system relies on pressurized air, do not leave any of the power supply and fan tray slots empty longer 
than two minutes while the switch is operating. If a power supply or fan tray fails, leave it in the switch until it can be replaced.

Содержание Ruckus ICX 7750




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды