manualshive.com logo in svg

CommScope Ruckus ICX 7750, Руководство по установке оборудования

Поделиться
Скачать
CommScope Ruckus ICX 7750 Скачать руководство пользователя страница 53

Ruckus ICX 7750 Switch Hardware Installation Guide 

51

Part Number: 53-1003900-10

 

Ruckus ICX 7750 Operation

•

LED activity interpretation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  51

•

Ruckus ICX 7750 front-panel LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  51

•

Ruckus ICX 7750 rear-panel LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  54

•

LED patterns  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  55

•

Diagnostic tests and monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  58

•

Monitoring power and cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  58

LED activity interpretation

System activity and status can be determined through the activity of the LEDs on the switch.

There are three possible LED states: off (no light), a steady light, and a flashing light. Flashing lights may be slow, fast, or flickering. The 
LED colors are either green or amber.

Sometimes, the LEDs flash either of the colors during boot, POST, or other diagnostic tests. This is normal; it does not indicate a problem 
unless the LEDs do not indicate a healthy state after all boot processes and diagnostic tests are complete.

Ruckus ICX 7750 front-panel LEDs

The Ruckus ICX 7750-26Q has the following LEDs on the front panel:

•

Two power supply unit (PSU) bicolor status LEDs (green and amber) labeled PSU1 and PSU2

•

One DIAG LED bicolor status LED (green and amber)

•

One MS LED bicolor status LED (green and amber)

•

One HA LED bicolor status LED (green and amber)

•

One RDNT LED bicolor status LED (green and amber)

•

Four bicolor status LEDs (green and amber) for each of the 26 QSFP+ ports that indicate the status of the ports in 40 GbE 
mode and 4x10 GbE breakout mode

Figure 38

 shows the LEDs on the Ruckus ICX 7750-26Q front panel.

Содержание Ruckus ICX 7750




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды