CommScope Ruckus ICX 7750 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 91

CommScope Ruckus ICX 7750 Скачать руководство пользователя страница 30

28

Ruckus ICX 7750 Switch Hardware Installation Guide

Part Number: 53-1003900-10

Installing the Ruckus ICX 7750

Installing the 1U, 1.5U, and 2U Universal Kit for Four-Post Racks (XBR-R000295)

NOTE

The illustrations in the rack installation procedures show a 1U device, but the instructions are the same for a 1.5U or 2U device.
The illustrations in the rack installation procedures are for reference only and may not show the actual device.

Complete the following tasks to install the device in a four-post rack:

1.

“Attaching the front brackets”

2.

“Attaching the extension brackets to the device”

3.

“Installing the device in the rack”

4.

“Attaching the rear brackets to the extensions”

5.

“Attaching the rear brackets to the rack posts”

Attaching the front brackets

Complete the following steps to attach the front brackets to the device.

1.

Position the right front bracket with the flat side against the right side of the device at the front of the device, as shown in

2.

Insert four 8-32 x 5/16-in. flathead screws through the vertically aligned holes in the bracket and then into the holes on the side
of the device. Use the upper and lower screw holes, leaving the center holes empty.

3.

Repeat Step 1 and Step 2 to attach the left front bracket to the left side of the device.

4.

Tighten all the 8-32 x 5/16-in. screws to a torque of 15 in-lb (17 cm-kg).

FIGURE 15

Attaching the front brackets

«
...
28
29
30
31
32
...
»

Содержание Ruckus ICX 7750




























































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды