manualshive.com logo in svg

CommScope Ruckus ICX 7750, Руководство по установке оборудования

Поделиться
Скачать
CommScope Ruckus ICX 7750 Скачать руководство пользователя страница 26

24

Ruckus ICX 7750 Switch Hardware Installation Guide 

Part Number: 53-1003900-10

Installing the Ruckus ICX 7750

Installing the device in a rack

 

Installing the device in a rack

NOTE

You need a #2 Phillips screwdriver for installation.

Before mounting the switch in a rack, pay particular attention to the following factors:

•

Temperature: Because the temperature within a rack assembly may be higher than the ambient room temperature, check that 
the rack-environment temperature is within the specified operating temperature range. (Refer to 

“Environmental considerations”

 

on page 20.)

•

Mechanical loading: Do not place any equipment on top of a rack-mounted unit.

•

Circuit overloading: Be sure that the supply circuit to the rack assembly is not overloaded.

•

Grounding: Rack-mounted equipment should be properly grounded. Particular attention should be given to supply connections 
other than direct connections to the mains electricity supply.

To mount the product into a four-post rack, you can order a four-post rack kit with the part number XBR-R000295. For the procedure to 
install this kit, refer to 

“Installing the 1U, 1.5U, and 2U Universal Kit for Four-Post Racks (XBR-R000295)”

 on page 26.

Two-post rack mount installation

The Ruckus ICX 7750 can be installed in a two-post rack in various mounting positions, as shown in 

Figure 11

. 

FIGURE 11

Two-post rack mounting positions

DANGER

Make sure the rack housing the device is adequately secured to prevent it from becoming unstable or falling over.

1

Front flush mount

4

Reverse mid-mount

2

Reverse-front mount

5

Rear mount

3

Front mid-mount

6

2-post rack, side view

Содержание Ruckus ICX 7750




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды