manualshive.com logo in svg

CommScope Ruckus ICX 7750, Руководство по установке оборудования

Поделиться
Скачать
CommScope Ruckus ICX 7750 Скачать руководство пользователя страница 28

26

Ruckus ICX 7750 Switch Hardware Installation Guide 

Part Number: 53-1003900-10

Installing the Ruckus ICX 7750

Installing the 1U, 1.5U, and 2U Universal Kit for Four-Post Racks (XBR-R000295)

 

FIGURE 13

Installing the Ruckus ICX 7750 in a 2-post rack

Proceed to 

“Grounding the system”

 on page 37.

Installing the 1U, 1.5U, and 2U Universal Kit for Four-Post Racks 
(XBR-R000295)

Use the following instructions to install a 1U, 1.5U, or 2U device in a 19-in. (48.3 cm) EIA rack using the 1U, 1.5U, and 2U Universal Kit 
for Four-Post Racks (XBR-R000295).

The device can be installed so that the port side is either flush with the front posts or recessed with the non-port side flush with the rear 
posts. A recessed position allows a more gradual bend in the fiber-optic cables connected to the device and less interference in the aisle 
at the front of the rack.

NOTE

Hardware devices illustrated in these procedures are only for reference and may not depict the device you are installing into the 
rack.

Installation requirements

Review the installation and facility requirements for your product before mounting the device. Refer to the hardware installation guide for 
your product for more information.

Use Electronic Industries Association (EIA) standard racks. Provide space in a 19-in. (48.3 cm) EIA rack, as required for the device type, 
with a minimum distance of 24 in. (609.60 mm) and a maximum distance of 32 in. (812.80 mm) between the front and back posts.

Time and items required

Allow 15 to 30 minutes to complete this procedure. Note the following requirements to ensure correct installation and operation.

The following items are required to install the device using the Universal Four-Post Rack Kit:

•

Clamps or other means of temporarily supporting the device in the rack

Содержание Ruckus ICX 7750




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды