manualshive.com logo in svg

CommScope Ruckus ICX 7750, Руководство по установке оборудования

Поделиться
Скачать
CommScope Ruckus ICX 7750 Скачать руководство пользователя страница 49

Ruckus ICX 7750 Switch Hardware Installation Guide 

47

Part Number: 53-1003900-10

Installing the Ruckus ICX 7750

Stacking Ruckus ICX 7750 switches

 

Stacking cables

Use QSFP+ direct attached active copper stacking cables or QSFP+ fiber optic cables to connect Ruckus ICX 7750 devices in a stack. 
The copper cable lengths for 40 GbE ports are 1 meter, 3 meters, and 5 meters.

Extended distance stacking

Because Ruckus ICX 7750 devices use Ethernet for the inter-switch stack connections, the deployment options are greatly increased. If 
standard copper stacking cables are used, the inter-switch connections can be up to 5 meters, which is usually sufficient for locally 
distributed stacks such as in top-of-rack (ToR) applications. For broader distribution, fiber-optic cables should be used, allowing a stack to 
be deployed across multiple physical locations such as the wiring closets of an office building. 

NOTE

The use of 40GBASE-LR4 optics for extended distance stacking is supported only in the default stacking ports (1/2/1, 1/2/4, 
1/3/1, or 1/3/4). Due to the limitation on the Ruckus ICX7750-48C and the ICX7750-48F, where 40GBASE-LR4 optics are 
supported only in ports 1/2/5, 1/2/6, 1/3/5, or 1/3/6, extended distance stacking is not supported for 40GBASE-LR4 optics.

Table 9

 shows the approved optics and stacking distance combinations.

Stack size

The Ruckus ICX 7750 supports up to 12 units in a stack. You can mix any number of Ruckus ICX 7750-26Q, Ruckus ICX 7750-48F, 
or Ruckus ICX 7750-48C devices together in a stack.

Stacking topologies

Both linear and ring topologies are supported in a stack. In a linear stack topology, there is a connection between each switch that carries 
two-way communications across the stack. 

For example, in a three-unit stack using a linear topology, unit 1 connects to unit 2, and unit 2 connects to unit 3.

Figure 34

 shows a supported rear panel linear stacking topology. 

TABLE 9

Fiber-optic options and stacking distances

Stacking cable option

Description

Maximum stacking distance

40GBase-SR4 fiber-optic cable

40G QSFP-QSFP

100 meter

40GBase-ESR4 fiber-optic cable

40G QSFP-QSFP

300 meter (OM3 multimode fiber)

400 meter (OM4 multimode fiber)

40GBase-LR4 fiber-optic cable

40G QSFP-QSFP

10 kilometers for ICX 7750-26Q device only

Содержание Ruckus ICX 7750




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды