manualshive.com logo in svg

CommScope Ruckus ICX 7750, Руководство по установке оборудования

Поделиться
Скачать
CommScope Ruckus ICX 7750 Скачать руководство пользователя страница 69

Ruckus ICX 7750 Switch Hardware Installation Guide 

67

Part Number: 53-1003900-10

Managing the Ruckus ICX 7750

Replacing an expansion module

 

Installing or replacing an expansion module

NOTE

The Ruckus ICX 7750 must be powered off before installing or replacing an expansion module.

Complete the following steps to install or replace an expansion module in the Ruckus ICX 7750.

1.

If replacing an expansion module:

a.

Pull the release latch lever on the module into its open position.

b.

Using a Phillips screwdriver, unscrew the two captive screws on the expansion module.

c.

Remove the expansion module from the chassis by pulling the handle on the expansion module out and away from the 
chassis.

2.

If installing a new expansion module into a slot covered with a filler panel:

a.

Using a Phillips screwdriver, unscrew the captive screws on the filler panel.

b.

Remove the filler panel.

3.

Before opening the package that contains the new expansion module, touch the bag to the switch casing to discharge any 
potential static electricity. It is recommended that you wear an ESD wrist strap during installation.

4.

Remove the expansion module from the anti-static shielded bag.

NOTE

Do not force the installation. If the expansion module does not slide in easily, ensure that it is correctly oriented before continuing.

5.

Holding the expansion module level, guide it into the carrier rails on each side and gently push it all the way into the slot, ensuring 
that it firmly engages with the connector.

6.

When you are sure the expansion module has properly engaged the connector, tighten the captive screws to secure the 
expansion module in the slot.

7.

Push the release latch lever on the module into its closed position.

8.

Verify correct installation by running the 

show chassis

 command.

CAUTION

If you do not install a power supply in a slot, you must keep the slot panel in place. If you run the device with an uncovered slot, 
the system will overheat.

Содержание Ruckus ICX 7750




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды