manualshive.com logo in svg

CommScope Ruckus ICX 7750, Руководство по установке оборудования

Поделиться
Скачать
CommScope Ruckus ICX 7750 Скачать руководство пользователя страница 54

52

Ruckus ICX 7750 Switch Hardware Installation Guide 

Part Number: 53-1003900-10

Ruckus ICX 7750 Operation

Ruckus ICX 7750 front-panel LEDs

 

FIGURE 38

Ruckus ICX 7750-26Q front-panel LEDs

The Ruckus ICX 7750-48C has the following LEDs on the front panel:

•

Two power supply unit (PSU) bicolor status LEDs (green and amber) labeled PSU1 and PSU2

•

One DIAG LED bicolor status LED (green and amber)

•

One MS LED bicolor status LED (green and amber)

•

One HA LED bicolor status LED (green and amber)

•

One RDNT LED bicolor status LED (green and amber)

•

48 1/10 GbE bicolor status LEDs (green for 10 GbE and amber for 1 GbE) which indicate 1 GbE or 10 GbE mode of operation

•

Four bicolor status LEDs (green and amber) for each of the six QSFP+ ports that indicate the status of the ports in 40 GbE mode 
and 4x10 GbE breakout mode

Figure 39

 shows the LEDs on the Ruckus ICX 7750-48C front panel. The up-arrow port status LEDs for the 1/10 GbE ports 

correspond to the upper, odd-numbered ports; the down-arrow port status LEDs correspond to the lower, even-numbered ports.

1

PSU1 and PSU2 status LEDs 
(PSU1 corresponds to the right power supply slot 
on the rear panel and PSU2 corresponds to the left 
power supply slot, as viewed from the rear)

7

Upper slot 10 GbE mode lane 4 link/activity LED

2

MS and DIAG status LEDs

8

Lower slot 40 GbE mode link/activity LED or 10 
GbE mode lane 1 link/activity LED

3

HA and RDNT status LEDs

9

Lower slot 10 GbE mode lane 2 link/activity LED

4

Upper slot 40 GbE mode link/activity LED or 
10 GbE mode lane 1 link/activity LED

10 Lower slot 10 GbE mode lane 3 link/activity LED

5

Upper slot 10 GbE mode lane 2 link/activity LED

11 Lower slot 10 GbE mode lane 4 link/activity LED

6

Upper slot 10 GbE mode lane 3 link/activityy LED

Содержание Ruckus ICX 7750




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды