manualshive.com logo in svg

CommScope Ruckus ICX 7750, Руководство по установке оборудования

Поделиться
Скачать
CommScope Ruckus ICX 7750 Скачать руководство пользователя страница 90

88

Ruckus ICX 7750 Switch Hardware Installation Guide 

Part Number: 53-1003900-10

Ruckus ICX 7750 Cautions and Danger Notices

Danger notices

 

  

  

 

DANGER

If the installation requires a different power cord than the one supplied with the device, make sure you use a power cord 
displaying the mark of the safety agency that defines the regulations for power cords in your country. The mark is your 
assurance that the power cord can be used safely with the device.

GEFAHR

Falls für die Installation ein anderes Stromkabel erforderlich ist (wenn das mit dem Gerät gelieferte Kabel nicht passt), müssen 
Sie sicherstellen, dass Sie ein Stromkabel mit dem Siegel einer Sicherheitsbehörde verwenden, die für die Zertifizierung von 
Stromkabeln in Ihrem Land zuständig ist. Das Siegel ist Ihre Garantie, dass das Stromkabel sicher mit Ihrem Gerät verwendet 
werden kann.

DANGER

Si l'installation nécessite un cordon d'alimentation autre que celui fourni avec le dispositif, assurez-vous d'utiliser un cordon 
d'alimentation portant la marque de l'organisation responsable de la sécurité qui définit les normes et régulations pour les 
cordons d'alimentation dans votre pays. Cette marque vous assure que vous pouvez utiliser le cordon d'alimentation avec le 
dispositif en toute sécurité.

PELIGRO

Si la instalación requiere un cordón de corriente distinto al que se ha suministrado con el instrumento, verifique que usa un 
cordón de corriente que venga con la marca de la agencia de seguridad que defina las regulaciones para cordones de corriente 
en su país. Esta marca será su garantía de que el cordón de corriente puede ser utilizado con seguridad con el instrumento.

DANGER

Laser radiation. Do not view directly with optical instruments. Class 1M laser products.

GEFAHR

Laserstrahlung! Schauen Sie nicht direkt mit optischen Instrumenten in den Laserstrahl herein. Klasse 1M Laserprodukte.

DANGER

Rayonnement de laser. Ne regardez pas directement avec les instruments optiques. Produits de laser de la classe 1M.

PELIGRO

Radiacion de Laser. No vea directamente con Instrumentos Opticos. Clase 1M de Productos de Laser.

DANGER

Remove both power cords before servicing.

GEFAHR

Trennen Sie beide Netzkabel, bevor Sie Wartungsarbeiten durchführen.

DANGER

Retirez les deux cordons d'alimentation avant toute maintenance.

PELIGRO

Desconecte ambos cables de alimentación antes de realizar reparaciones.

DANGER

To avoid high voltage shock, do not open the device while the power is on.

GEFAHR

Das eingeschaltete Gerät darf nicht geöffnet werden, da andernfalls das Risiko eines Stromschlags mit Hochspannung besteht.

DANGER

Afin d'éviter tout choc électrique, n'ouvrez pas l'appareil lorsqu'il est sous tension.

PELIGRO

Para evitar una descarga de alto voltaje, no abra el dispositivo mientras esté encendido.

Содержание Ruckus ICX 7750




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды