manualshive.com logo in svg

CommScope Ruckus ICX 7750, Руководство по установке оборудования

Поделиться
Скачать
CommScope Ruckus ICX 7750 Скачать руководство пользователя страница 56

54

Ruckus ICX 7750 Switch Hardware Installation Guide 

Part Number: 53-1003900-10

Ruckus ICX 7750 Operation

Ruckus ICX 7750 rear-panel LEDs

 

FIGURE 40

Ruckus ICX 7750-48F front-panel LEDs

Ruckus ICX 7750 rear-panel LEDs

The Ruckus ICX 7750 has the following LEDs on the rear panel:

•

Two Management port status LEDs

•

Two stack control path port LEDs (currently not used)

•

Expansion module LEDs:

•

One Power LED bicolor status LED (green and amber)

•

Four bicolor status LEDs (green and amber) for each of the six QSFP+ ports that indicate the status of the ports in 40 GbE 
mode and 4x10 GbE breakout mode

•

Power supply LEDs: One status LED on each installed power supply

•

Fan tray LEDs: One status LED on each installed fan tray

Figure 41

 shows the LEDs on the rear panel of the Ruckus ICX 7750.

1

Upper 1/10 GbE port LEDs

4

MS and DIAG status LEDs

2

Lower 1/10 GbE port LEDs

5

HA and RDNT status LEDs

3

PSU1 and PSU2 status LEDs 
(PSU1 corresponds to the right power supply slot 
on the rear panel and PSU2 corresponds to the left 
power supply slot, as viewed from the rear)

Содержание Ruckus ICX 7750




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды