Citizen CL-E700 Series Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 236

background image

Chapter 2 Operating Principles

2-1.

Operation of Each Mechanism

CL-E700 series

2-8

2-1-3. Label/Tag Detection Mechanism

The major components of the label/tag detection mechanism are:
(a) SA Ref Sensor PCB (Bottom sensor, Reflective sensor)
(b) SA TRA Sen PCB (Upper sensor, Transparent sensor)

There are two sensors, the reflective sensor (bottom sensor) and the transparent sensor (upper
sensor). As shown in the figure blow, the reflective sensor has two LEDs and one phototransistor.
The reflective sensor is used to detect black marks on the back of tag. On the other hand, the
transparent sensor is a phototransistor that receives the transparent light from the reflective
sensor’s LEDs through the media. The transparent sensor is used to detect labels on liner or
U-shaped notches of tag. Both reflective and transparent sensors are used to detect the media
end.

Aligning the sensors for label paper, and tag with U-shaped notches:

For label paper, align both reflective and transparent sensors at the center of the label. For tags
with U-shaped notches, align both sensors with the U-shaped notch. In both cases, align the arrow
mark of the transparent sensor with the right side mark of the reflective sensor as shown below.

Aligning the reflective sensor for tag with black marks:

For tag with black marks, align the reflective sensor alone with the black mark. In this case, align
the left side mark of the reflective sensor with the black mark as shown below.

Phototransistor

LEDs

Photo-

transistor

Transparent

Sensor

Reflective

Sensor

[For label paper/tag with
U-shaped notches]
* Both sensors are used.

[For tag with black marks]

* Reflective sensors alone is used.

Transparent

Sensor

Reflective Sensor

Black mark

Reflective Sensor

«
...
20
21
22
23
24
...
»

Содержание CL-E700 Series













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CL-E700 Series

Бренд: Gallagher Страницы: 13

Бренд: Jadak Страницы: 83

ACR1281U-C1 Dualboost 2

Бренд: ACS Страницы: 16

Бренд: ASIS Technologies Страницы: 10

Бренд: Cognex Страницы: 47

Бренд: Microscan Страницы: 10

MULTI-CARD 25-IN-1

Бренд: Lexar Страницы: 10

Бренд: G4S Страницы: 2

Бренд: Infinite Peripherals Страницы: 4

Бренд: Unitech Страницы: 2

Бренд: Atid Страницы: 2

Бренд: Atid Страницы: 30

Бренд: Atid Страницы: 35

Бренд: Siemens Страницы: 34

Бренд: clare Страницы: 3

Бренд: BBPOS Страницы: 2

Бренд: Datalogic Страницы: 59

Бренд: Anviz Страницы: 85

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды