Cisco Catalyst 6816-X-LE Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 100

background image

Power Supply Slots

The chassis has two power supply slots that accept either AC-input or DC-input power supplies, or one of
each. The chassis is delivered with power supplies pre-installed in the power supply slots. If only one power
supply is ordered, then a blank cover is installed in the empty power supply slot, which must remain installed
if a power supply is not installed.

Table 6: Power supplies supported by the switches

Power Supply

Switch

750W and 1100W

Catalyst 6816-X-LE

750W and 1100W

Catalyst 6832-X-LE

750W and 1100W

Catalyst 6824-X-LE-40G

1100W

If you insert a 750W power supply in to
the power supply slot of a Catalyst
6840-X-LE-40G switch, the switch fails
to boot.

Note

Catalyst 6840-X-LE-40G

Related Topics

Front Panel Components

Management Port

The management port is a 10/100/1000 copper Ethernet port directly connected to the route processor. The
switch also has a fibre port that can be used as the Ethernet Management port. It supports TFTP image
downloading, network management, SNMP, Telnet, and SSH connections. Flexible NetFlow export is not
supported on the management port. The management port is isolated from other ports in the system in a
dedicated management VRF; it is not part of the EARL forwarding logic. The management port provides
direct access to the CPU, even when the system is heavily loaded.

The management port is a Layer 3 port in host mode, and only accepts traffic that terminates on the router.
This port does not route packets between itself and other ports. The port processes only the following packet
types and properly enqueues them:

• Address Resolution Protocol (ARP)

• IPv4 unicast

• IPv6 unicast

• Cisco Discovery Protocol (CDP)

• Link Layer Discovery Protocol (LLDP)

Related Topics

Front Panel Components

Catalyst 6840-X Switch Series Hardware Installation Guide

13

Product Overview

Power Supply Slots

«
...
23
24
25
26
27
...
»

Содержание Catalyst 6816-X-LE





































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 6816-X-LE

Бренд: Manhattan Страницы: 2

Бренд: Edge-Core Страницы: 9

Бренд: Paugge Страницы: 20

Бренд: Edge-Core Страницы: 12

KingShield T206-C

Бренд: Green Brook Страницы: 2

Бренд: tactio Страницы: 2

Бренд: Lantech Страницы: 29

Бренд: TRENDnet Страницы: 2

Бренд: rako Страницы: 5

Бренд: AV Link Страницы: 2

Бренд: KDS Страницы: 10

PSEN ma2.1p/ATEX

Бренд: Pilz Страницы: 8

Бренд: ENSIM SENSORS Страницы: 15

Бренд: DataParts Страницы: 4

Бренд: Pliant Страницы: 49

Бренд: Lantech Страницы: 27

Guardian Line Series

Бренд: IDEM SAFETY SWITCHES Страницы: 4

SAN16B-2 - TotalStorage Express Model Switch

Бренд: IBM Страницы: 93

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды