Cisco Catalyst 6816-X-LE Скачать руководство пользователя страница 54

Страница: 54 / 100

Figure 18: Installing the chassis on a Rack with a 17.75 in. (45.09 cm) Opening

Installing the Chassis in a Two-Post Rack

The chassis are designed to be mounted in equipment racks that meet ANSI/EIA 310-D and ETS 300-119
standards.

Note

Procedure

Step 1

Before rack-mounting the chassis, determine if you need to move the L brackets so that the chassis is installed
in one of the recommended positions:

• Positioned so the front of the chassis is approximately flush with the front of the rack:

• The chassis is shipped with the L brackets in the correct location; there is no need to move them.

• Positioned so approximately one fourth of the chassis protrudes in front of the rack:

• Remove the screws in the L brackets.

• Reposition the L brackets to align with the first set of holes behind the holes where the L brackets

were originally installed (see figure below).

• Secure the brackets with the screws.

Catalyst 6840-X Switch Series Hardware Installation Guide

Installing the Switch

Installing the Chassis in a Two-Post Rack

Содержание Catalyst 6816-X-LE





































































































Результаты поиска

Содержание Catalyst 6816-X-LE

Отзывы:

Похожие инструкции для Catalyst 6816-X-LE

Бренды по названию

Популярные бренды

Cisco Catalyst 6816-X-LE, Руководство по установке оборудования

Результаты поиска

Содержание Catalyst 6816-X-LE

Отзывы:

Похожие инструкции для Catalyst 6816-X-LE

Бренды по названию

Популярные бренды