Cisco Catalyst 6816-X-LE Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 100

background image

• 1 stop bits

Connecting the Uplink Ports

SFP and SFP+ Transceiver Modules

The SFP and SFP+ transceiver modules provide copper or fiber-optic connections to other devices. These
transceiver modules are field-replaceable and provide the uplink interfaces when installed in an SFP module
slot. The SFP modules have LC connectors for fiber-optic connections or RJ-45 connectors for copper
connections.

For Cisco SFP and SFP+ transceiver modules documentation, including compatibility matrixes, refer to this
URL:

http://www.cisco.com/en/US/products/hw/modules/ps5455/products_device_support_tables_list.html

Installing SFP and SFP+ Transceiver Modules

Before you begin

For cable specifications, see Appendix B, “Connector and Cable Specifications.”

Observe these precautions:

Class 1 laser product. Statement 1008

Warning

• Do not remove the dust plugs from the SFP transceiver modules or the rubber caps from the fiber-optic

cable until you are ready to connect the cable. The plugs and caps protect the module ports and cables
from contamination and ambient light.

• Removing and installing an SFP transceiver module can shorten its useful life. Do not remove and insert

any SFP transceiver module more often than is necessary.

• To prevent ESD damage, follow your normal board and component handling procedures when connecting

cables to the switch and other devices.

Procedure

Step 1

Attach an ESD-preventive wrist strap to your wrist and to an earth ground surface.

Step 2

Find the send (Tx) and receive (Rx) markings that identify the top of the SFP module.

On some SFP transceiver modules, the send and receive (Tx and Rx) markings might be shown by arrows
that show the direction of the connection.

Step 3

If the SFP transceiver module has a bale-clasp latch, move it to the open, unlocked position.

Step 4

Align the module in front of the slot opening, and push until you feel the connector snap into place.

Catalyst 6840-X Switch Series Hardware Installation Guide

48

Installing the Switch

Connecting the Uplink Ports

«
...
58
59
60
61
62
...
»

Содержание Catalyst 6816-X-LE





































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 6816-X-LE

Бренд: Talkswitch Страницы: 17

Бренд: 3Com Страницы: 128

Бренд: 3Com Страницы: 2

Бренд: 3Com Страницы: 422

3CR16708-91 - OfficeConnect Managed Switch 9

Бренд: 3Com Страницы: 4

Бренд: 3Com Страницы: 5

Бренд: 3Com Страницы: 30

Бренд: 3Com Страницы: 36

Бренд: 3Com Страницы: 4

Baseline 2226-PWR Plus

Бренд: 3Com Страницы: 77

Бренд: 3Com Страницы: 570

OfficeConnect WX1200

Бренд: 3Com Страницы: 28

Baseline 2226-PWR Plus

Бренд: 3Com Страницы: 4

CoreBuilder 6000

Бренд: 3Com Страницы: 31

Бренд: PRO SIGNAL Страницы: 5

Underwater Switch 24V DC/DMX/02

Бренд: Oase Страницы: 40

Бренд: Vega Страницы: 28

Бренд: SMART Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды