Cisco Catalyst 6816-X-LE Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 100

background image

This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation.
Install only in accordance with national and local wiring regulations. Statement 1045

Warning

When installing or replacing the unit, the ground connection must always be made first and disconnected last.
Statement 1046

Warning

Installation of the equipment must comply with local and national electrical codes.. Statement 1074

Warning

Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or
view directly with optical instruments. Statement 1051

Warning

Before starting the installation procedures in this chapter, see the “Site Preparation Checklist” section on page
2-15 to verify that all site planning activities were completed.

Rack-Mounting Guidelines

The switch is designed to be installed in standard 19-inch racks.

Note

Before rack-mounting the switch, ensure that the equipment rack complies with the following guidelines:

• The width of the rack, measured between the two front-mounting strips or rails, must be one of the

following measurements:

• 17.5 inches (44.45 cm)

• 17.75 inches (45.09 cm)

• The depth of the rack, measured between the front- and rear-mounting strips, must be at least 19.25

inches (48.9 cm).

• The rack must have sufficient vertical clearance to insert the chassis: 8.75 inches (22.23 cm) (5 RU)

Chassis height is sometimes measured in rack units (RU or just U) where 1 RU or 1 U equals 1.75 in (44.45
mm). A typical server rack is 42 RU or 42 U in height.

Note

If the rack is on wheels, ensure that the brakes are engaged and that the rack is stabilized.

Caution

Catalyst 6840-X Switch Series Hardware Installation Guide

37

Installing the Switch

Rack-Mounting Guidelines

«
...
47
48
49
50
51
...
»

Содержание Catalyst 6816-X-LE





































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 6816-X-LE

Бренд: Keithley Страницы: 66

Бренд: Campbell Страницы: 14

Бренд: Maipu Страницы: 21

Бренд: Maico Страницы: 56

SynOptics 3000 Series

Бренд: Cabletron Systems Страницы: 101

Бренд: ASTEK Страницы: 3

Бренд: Sarowin Страницы: 9

Бренд: Kohler Страницы: 170

MMAC-Plus 9T125-24

Бренд: Cabletron Systems Страницы: 36

Бренд: Pakedge Страницы: 12

Бренд: ADS Technologies Страницы: 2

Cordex HP CXRF 48-2.4kW

Бренд: Alpha Страницы: 56

Бренд: SMART-AVI Страницы: 2

Бренд: Synergy Global Technology Страницы: 9

Бренд: Huanyu Страницы: 10

Бренд: DataParts Страницы: 5

Бренд: Dell Страницы: 2

Бренд: HP Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды